Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Linux version 2.6.37-rc6 (rdunlap@control.site) (gcc version 4.4.1 20090725 (Red Hat 4.4.1-2) (GCC) ) #1 SMP Tue Dec 28 11:04:44 PST 2010 Command line: ro root=/dev/sda6 selinux=0 debug ignore_loglevel initcall_debug printk.time=1 print_fatal_signals=1 console=tty0 console=ttyS0,115200n8 netconsole=6666@192.168.1.5/eth0,6666@192.168.1.4/00:19:D1:7F:67:14 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007f686c00 (usable) BIOS-e820: 000000007f686c00 - 000000007f688c00 (ACPI NVS) BIOS-e820: 000000007f688c00 - 000000007f68ac00 (ACPI data) BIOS-e820: 000000007f68ac00 - 0000000080000000 (reserved) BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fed00400 (reserved) BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) NX (Execute Disable) protection: active DMI 2.3 present. DMI: 0HH807/OptiPlex GX620 , BIOS A07 03/31/2006 e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) e820 remove range: 00000000000a0000 - 0000000000100000 (usable) No AGP bridge found last_pfn = 0x7f686 max_arch_pfn = 0x400000000 MTRR default type: uncachable MTRR fixed ranges enabled: 00000-9FFFF write-back A0000-BFFFF uncachable C0000-CFFFF write-protect D0000-EFFFF uncachable F0000-FFFFF write-protect MTRR variable ranges enabled: 0 base 000000000 mask F80000000 write-back 1 base 07F800000 mask FFF800000 uncachable 2 base 07F700000 mask FFFF00000 uncachable 3 disabled 4 disabled 5 disabled 6 disabled 7 disabled x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 found SMP MP-table at [ffff8800000fe710] fe710 Scanning 0 areas for low memory corruption initial memory mapped : 0 - 20000000 init_memory_mapping: 0000000000000000-000000007f686000 0000000000 - 007f686000 page 4k kernel direct mapping tables up to 7f686000 @ 1fc01000-20000000 RAMDISK: 37be4000 - 37ff0000 ACPI: RSDP 00000000000feb00 00024 (v02 DELL ) ACPI: XSDT 00000000000fd24f 0005C (v01 DELL GX620 00000007 ASL 00000061) ACPI: FACP 00000000000fd347 000F4 (v03 DELL GX620 00000007 ASL 00000061) ACPI: DSDT 00000000fffd32f4 03D69 (v01 DELL dt_ex 00001000 INTL 20050309) ACPI: FACS 000000007f686c00 00040 ACPI: SSDT 00000000fffd717c 000AA (v01 DELL st_ex 00001000 INTL 20050309) ACPI: APIC 00000000000fd43b 00072 (v01 DELL GX620 00000007 ASL 00000061) ACPI: BOOT 00000000000fd4ad 00028 (v01 DELL GX620 00000007 ASL 00000061) ACPI: ASF! 00000000000fd4d5 00067 (v16 DELL GX620 00000007 ASL 00000061) ACPI: MCFG 00000000000fd53c 0003E (v01 DELL GX620 00000007 ASL 00000061) ACPI: HPET 00000000000fd57a 00038 (v01 DELL GX620 00000007 ASL 00000061) ACPI: Local APIC address 0xfee00000 No NUMA configuration found Faking a node at 0000000000000000-000000007f686000 Initmem setup node 0 0000000000000000-000000007f686000 NODE_DATA [000000007f655000 - 000000007f685fff] [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff88007ce00000-ffff88007e9fffff] on node 0 Zone PFN ranges: DMA 0x00000010 -> 0x00001000 DMA32 0x00001000 -> 0x00100000 Normal empty Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000010 -> 0x000000a0 0: 0x00000100 -> 0x0007f686 On node 0 totalpages: 521750 DMA zone: 56 pages used for memmap DMA zone: 7 pages reserved DMA zone: 3921 pages, LIFO batch:0 DMA32 zone: 7079 pages used for memmap DMA32 zone: 510687 pages, LIFO batch:31 ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled) ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1]) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Using ACPI (MADT) for SMP configuration information ACPI: HPET id: 0x8086a201 base: 0xfed00000 SMP: Allowing 4 CPUs, 2 hotplug CPUs nr_irqs_gsi: 40 PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000 PM: Registered nosave memory: 00000000000f0000 - 0000000000100000 Allocating PCI resources starting at 80000000 (gap: 80000000:70000000) Booting paravirtualized kernel on bare hardware setup_percpu: NR_CPUS:4096 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 PERCPU: Embedded 477 pages/cpu @ffff88007c600000 s1924672 r8192 d20928 u2097152 pcpu-alloc: s1924672 r8192 d20928 u2097152 alloc=1*2097152 pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 Built 1 zonelists in Node order, mobility grouping on. Total pages: 514608 Policy zone: DMA32 Kernel command line: PID hash table entries: 4096 (order: 3, 32768 bytes) Checking aperture... No AGP bridge found Calgary: detecting Calgary via BIOS EBDA area Calgary: Unable to locate Rio Grande table in EBDA - bailing! Memory: 2012528k/2087448k available (5468k kernel code, 448k absent, 74472k reserved, 7434k data, 3116k init) SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 Hierarchical RCU implementation. RCU debugfs-based tracing is enabled. Hierarchical RCU autobalancing is disabled. RCU dyntick-idle grace-period acceleration is enabled. NR_IRQS:262400 nr_irqs:712 16 Console: colour VGA+ 80x25 console [tty0] enabled Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar ... MAX_LOCKDEP_SUBCLASSES: 8 ... MAX_LOCK_DEPTH: 48 ... MAX_LOCKDEP_KEYS: 8191 ... CLASSHASH_SIZE: 4096 ... MAX_LOCKDEP_ENTRIES: 16384 ... MAX_LOCKDEP_CHAINS: 32768 ... CHAINHASH_SIZE: 16384 memory used by lock dependency info: 6335 kB per task-struct memory footprint: 2688 bytes allocated 20971520 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups ODEBUG: 9 of 9 active objects replaced hpet clockevent registered Fast TSC calibration using PIT Detected 2992.532 MHz processor. Calibrating delay loop (skipped), value calculated using timer frequency.. 5985.06 BogoMIPS (lpj=11970128) pid_max: default: 32768 minimum: 301 Security Framework initialized AppArmor: AppArmor disabled by boot time parameter Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Mount-cache hash table entries: 256 Initializing cgroup subsys debug Initializing cgroup subsys ns ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup. Initializing cgroup subsys cpuacct Initializing cgroup subsys memory Initializing cgroup subsys devices Initializing cgroup subsys freezer CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 mce: CPU supports 4 MCE banks CPU0: Thermal monitoring enabled (TM1) using mwait in idle threads. numa_add_cpu cpu 0 node 0: mask now 0 Performance Events: Netburst events, Netburst P4/Xeon PMU driver. ... version: 0 ... bit width: 40 ... generic registers: 18 ... value mask: 000000ffffffffff ... max period: 0000007fffffffff ... fixed-purpose events: 0 ... event mask: 000000000003ffff ACPI: Core revision 20101013 ftrace: allocating 20237 entries in 80 pages Setting APIC routing to flat ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 CPU0: Intel(R) Pentium(R) D CPU 3.00GHz stepping 04 NMI watchdog enabled, takes one hw-pmu counter. lockdep: fixing up alternatives. Booting Node 0, Processors #1 numa_add_cpu cpu 1 node 0: mask now 0-1 NMI watchdog enabled, takes one hw-pmu counter. Brought up 2 CPUs Total of 2 processors activated (11970.60 BogoMIPS). devtmpfs: initialized gcov: version magic: 0x34303452 regulator: core version 0.5 regulator: dummy: NET: Registered protocol family 16 i2c-core: driver [dummy] registered ACPI: bus type pci registered PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000) PCI: MMCONFIG at [mem 0xf0000000-0xf3ffffff] reserved in E820 PCI: Using configuration type 1 for base access bio: create slab at 0 ACPI: EC: Look up EC in DSDT [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored ACPI: Interpreter enabled ACPI: (supports S0 S1 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: ACPI Dock Station Driver: 1 docks/bays found PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored) pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored) pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored) pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000effff] (ignored) pci_root PNP0A03:00: host bridge window [mem 0x000f0000-0x000fffff] (ignored) pci_root PNP0A03:00: host bridge window [mem 0x80000000-0xefffffff] (ignored) pci_root PNP0A03:00: host bridge window [mem 0xf4000000-0xfebfffff] (ignored) pci_root PNP0A03:00: host bridge window [mem 0xffa80800-0xffa80bff] (ignored) pci_bus 0000:00: scanning bus pci 0000:00:00.0: [8086:2770] type 0 class 0x000600 pci 0000:00:00.0: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:00.0: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:00.0: calling pci_fixup_transparent_bridge+0x0/0x44 pci 0000:00:01.0: [8086:2771] type 1 class 0x000604 pci 0000:00:01.0: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:01.0: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:01.0: calling pci_fixup_transparent_bridge+0x0/0x44 pci 0000:00:01.0: PME# supported from D0 D3hot D3cold pci 0000:00:01.0: PME# disabled pci 0000:00:02.0: [8086:2772] type 0 class 0x000300 pci 0000:00:02.0: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:02.0: reg 10: [mem 0xfeb00000-0xfeb7ffff] pci 0000:00:02.0: reg 14: [io 0xe898-0xe89f] pci 0000:00:02.0: reg 18: [mem 0xe0000000-0xefffffff pref] pci 0000:00:02.0: reg 1c: [mem 0xfeac0000-0xfeafffff] pci 0000:00:02.0: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:02.0: calling pci_fixup_transparent_bridge+0x0/0x44 pci 0000:00:02.1: [8086:2776] type 0 class 0x000380 pci 0000:00:02.1: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:02.1: reg 10: [mem 0xfeb80000-0xfebfffff] pci 0000:00:02.1: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:02.1: calling pci_fixup_transparent_bridge+0x0/0x44 pci 0000:00:1c.0: [8086:27d0] type 1 class 0x000604 pci 0000:00:1c.0: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:1c.0: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:1c.0: calling pci_fixup_transparent_bridge+0x0/0x44 pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold pci 0000:00:1c.0: PME# disabled pci 0000:00:1c.1: [8086:27d2] type 1 class 0x000604 pci 0000:00:1c.1: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:1c.1: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:1c.1: calling pci_fixup_transparent_bridge+0x0/0x44 pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold pci 0000:00:1c.1: PME# disabled pci 0000:00:1d.0: [8086:27c8] type 0 class 0x000c03 pci 0000:00:1d.0: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:1d.0: reg 20: [io 0xff80-0xff9f] pci 0000:00:1d.0: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:1d.0: calling pci_fixup_transparent_bridge+0x0/0x44 pci 0000:00:1d.1: [8086:27c9] type 0 class 0x000c03 pci 0000:00:1d.1: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:1d.1: reg 20: [io 0xff60-0xff7f] pci 0000:00:1d.1: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:1d.1: calling pci_fixup_transparent_bridge+0x0/0x44 pci 0000:00:1d.2: [8086:27ca] type 0 class 0x000c03 pci 0000:00:1d.2: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:1d.2: reg 20: [io 0xff40-0xff5f] pci 0000:00:1d.2: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:1d.2: calling pci_fixup_transparent_bridge+0x0/0x44 pci 0000:00:1d.3: [8086:27cb] type 0 class 0x000c03 pci 0000:00:1d.3: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:1d.3: reg 20: [io 0xff20-0xff3f] pci 0000:00:1d.3: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:1d.3: calling pci_fixup_transparent_bridge+0x0/0x44 pci 0000:00:1d.7: [8086:27cc] type 0 class 0x000c03 pci 0000:00:1d.7: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:1d.7: reg 10: [mem 0xffa80800-0xffa80bff] pci 0000:00:1d.7: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:1d.7: calling pci_fixup_transparent_bridge+0x0/0x44 pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold pci 0000:00:1d.7: PME# disabled pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604 pci 0000:00:1e.0: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:1e.0: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:1e.0: calling pci_fixup_transparent_bridge+0x0/0x44 pci 0000:00:1e.2: [8086:27de] type 0 class 0x000401 pci 0000:00:1e.2: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:1e.2: reg 10: [io 0xec00-0xecff] pci 0000:00:1e.2: reg 14: [io 0xe8c0-0xe8ff] pci 0000:00:1e.2: reg 18: [mem 0xfeabfa00-0xfeabfbff] pci 0000:00:1e.2: reg 1c: [mem 0xfeabf900-0xfeabf9ff] pci 0000:00:1e.2: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:1e.2: calling pci_fixup_transparent_bridge+0x0/0x44 pci 0000:00:1e.2: PME# supported from D0 D3hot D3cold pci 0000:00:1e.2: PME# disabled pci 0000:00:1f.0: [8086:27b8] type 0 class 0x000601 pci 0000:00:1f.0: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:1f.0: calling ich_force_enable_hpet+0x0/0x214 pci 0000:00:1f.0: calling quirk_ich7_lpc+0x0/0x95 pci 0000:00:1f.0: quirk: [io 0x0800-0x087f] claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: [io 0x0880-0x08bf] claimed by ICH6 GPIO pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0c00 (mask 007f) pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 00e0 (mask 0007) pci 0000:00:1f.0: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:1f.0: calling pci_fixup_transparent_bridge+0x0/0x44 pci 0000:00:1f.1: [8086:27df] type 0 class 0x000101 pci 0000:00:1f.1: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:1f.1: reg 10: [io 0x01f0-0x01f7] pci 0000:00:1f.1: reg 14: [io 0x03f4-0x03f7] pci 0000:00:1f.1: reg 18: [io 0x0170-0x0177] pci 0000:00:1f.1: reg 1c: [io 0x0374-0x0377] pci 0000:00:1f.1: reg 20: [io 0xffa0-0xffaf] pci 0000:00:1f.1: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:1f.1: calling pci_fixup_transparent_bridge+0x0/0x44 pci 0000:00:1f.2: [8086:27c0] type 0 class 0x000101 pci 0000:00:1f.2: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:1f.2: reg 10: [io 0xfe00-0xfe07] pci 0000:00:1f.2: reg 14: [io 0xfe10-0xfe13] pci 0000:00:1f.2: reg 18: [io 0xfe20-0xfe27] pci 0000:00:1f.2: reg 1c: [io 0xfe30-0xfe33] pci 0000:00:1f.2: reg 20: [io 0xfea0-0xfeaf] pci 0000:00:1f.2: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:1f.2: calling pci_fixup_transparent_bridge+0x0/0x44 pci 0000:00:1f.2: PME# supported from D3hot pci 0000:00:1f.2: PME# disabled pci 0000:00:1f.3: [8086:27da] type 0 class 0x000c05 pci 0000:00:1f.3: calling quirk_mmio_always_on+0x0/0x2a pci 0000:00:1f.3: reg 20: [io 0xe8a0-0xe8bf] pci 0000:00:1f.3: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:00:1f.3: calling pci_fixup_transparent_bridge+0x0/0x44 pci_bus 0000:00: fixups for bus pci 0000:00:01.0: scanning [bus 01-01] behind bridge, pass 0 pci_bus 0000:01: scanning bus pci_bus 0000:01: fixups for bus pci 0000:00:01.0: PCI bridge to [bus 01-01] pci 0000:00:01.0: bridge window [io 0xf000-0x0000] (disabled) pci 0000:00:01.0: bridge window [mem 0xfe900000-0xfe9fffff] pci 0000:00:01.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) pci_bus 0000:01: bus scan returning with max=01 pci 0000:00:1c.0: scanning [bus 02-02] behind bridge, pass 0 pci_bus 0000:02: scanning bus pci 0000:02:00.0: [14e4:1677] type 0 class 0x000200 pci 0000:02:00.0: calling quirk_mmio_always_on+0x0/0x2a pci 0000:02:00.0: reg 10: [mem 0xfe8f0000-0xfe8fffff 64bit] pci 0000:02:00.0: calling quirk_resource_alignment+0x0/0x1f7 pci 0000:02:00.0: PME# supported from D3hot D3cold pci 0000:02:00.0: PME# disabled pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' pci_bus 0000:02: fixups for bus pci 0000:00:1c.0: PCI bridge to [bus 02-02] pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled) pci 0000:00:1c.0: bridge window [mem 0xfe800000-0xfe8fffff] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) pci_bus 0000:02: bus scan returning with max=02 pci 0000:00:1c.1: scanning [bus 03-03] behind bridge, pass 0 pci_bus 0000:03: scanning bus pci_bus 0000:03: fixups for bus pci 0000:00:1c.1: PCI bridge to [bus 03-03] pci 0000:00:1c.1: bridge window [io 0xf000-0x0000] (disabled) pci 0000:00:1c.1: bridge window [mem 0xfe700000-0xfe7fffff] pci 0000:00:1c.1: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) pci_bus 0000:03: bus scan returning with max=03 pci 0000:00:1e.0: scanning [bus 04-04] behind bridge, pass 0 pci_bus 0000:04: scanning bus pci_bus 0000:04: fixups for bus pci 0000:00:1e.0: PCI bridge to [bus 04-04] (subtractive decode) pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled) pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff] (disabled) pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode) pci 0000:00:1e.0: bridge window [mem 0x00000000-0xfffffffff] (subtractive decode) pci_bus 0000:04: bus scan returning with max=04 pci 0000:00:01.0: scanning [bus 01-01] behind bridge, pass 1 pci 0000:00:1c.0: scanning [bus 02-02] behind bridge, pass 1 pci 0000:00:1c.1: scanning [bus 03-03] behind bridge, pass 1 pci 0000:00:1e.0: scanning [bus 04-04] behind bridge, pass 1 pci_bus 0000:00: bus scan returning with max=04 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI4._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI3._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15) ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 15) HEST: Table is not found! vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none vgaarb: loaded SCSI subsystem initialized libata version 3.00 loaded. PCI: Using ACPI for IRQ routing PCI: pci_cache_line_size set to 64 bytes pci 0000:00:02.0: BAR 0: reserving [mem 0xfeb00000-0xfeb7ffff flags 0x40200] (d=0, p=0) pci 0000:00:02.0: BAR 1: reserving [io 0xe898-0xe89f flags 0x40101] (d=0, p=0) pci 0000:00:02.0: BAR 2: reserving [mem 0xe0000000-0xefffffff flags 0x42208] (d=0, p=0) pci 0000:00:02.0: BAR 3: reserving [mem 0xfeac0000-0xfeafffff flags 0x40200] (d=0, p=0) pci 0000:00:02.1: BAR 0: reserving [mem 0xfeb80000-0xfebfffff flags 0x40200] (d=0, p=0) pci 0000:00:1d.0: BAR 4: reserving [io 0xff80-0xff9f flags 0x40101] (d=0, p=0) pci 0000:00:1d.1: BAR 4: reserving [io 0xff60-0xff7f flags 0x40101] (d=0, p=0) pci 0000:00:1d.2: BAR 4: reserving [io 0xff40-0xff5f flags 0x40101] (d=0, p=0) pci 0000:00:1d.3: BAR 4: reserving [io 0xff20-0xff3f flags 0x40101] (d=0, p=0) pci 0000:00:1d.7: BAR 0: reserving [mem 0xffa80800-0xffa80bff flags 0x40200] (d=0, p=0) pci 0000:00:1e.2: BAR 0: reserving [io 0xec00-0xecff flags 0x40101] (d=0, p=0) pci 0000:00:1e.2: BAR 1: reserving [io 0xe8c0-0xe8ff flags 0x40101] (d=0, p=0) pci 0000:00:1e.2: BAR 2: reserving [mem 0xfeabfa00-0xfeabfbff flags 0x40200] (d=0, p=0) pci 0000:00:1e.2: BAR 3: reserving [mem 0xfeabf900-0xfeabf9ff flags 0x40200] (d=0, p=0) pci 0000:00:1f.1: BAR 0: reserving [io 0x01f0-0x01f7 flags 0x110] (d=0, p=0) pci 0000:00:1f.1: BAR 1: reserving [io 0x03f6 flags 0x110] (d=0, p=0) pci 0000:00:1f.1: BAR 2: reserving [io 0x0170-0x0177 flags 0x110] (d=0, p=0) pci 0000:00:1f.1: BAR 3: reserving [io 0x0376 flags 0x110] (d=0, p=0) pci 0000:00:1f.1: BAR 4: reserving [io 0xffa0-0xffaf flags 0x40101] (d=0, p=0) pci 0000:00:1f.2: BAR 0: reserving [io 0xfe00-0xfe07 flags 0x40101] (d=0, p=0) pci 0000:00:1f.2: BAR 1: reserving [io 0xfe10-0xfe13 flags 0x40101] (d=0, p=0) pci 0000:00:1f.2: BAR 2: reserving [io 0xfe20-0xfe27 flags 0x40101] (d=0, p=0) pci 0000:00:1f.2: BAR 3: reserving [io 0xfe30-0xfe33 flags 0x40101] (d=0, p=0) pci 0000:00:1f.2: BAR 4: reserving [io 0xfea0-0xfeaf flags 0x40101] (d=0, p=0) pci 0000:00:1f.3: BAR 4: reserving [io 0xe8a0-0xe8bf flags 0x40101] (d=0, p=0) pci 0000:02:00.0: BAR 0: reserving [mem 0xfe8f0000-0xfe8fffff flags 0x140204] (d=0, p=0) reserve RAM buffer: 000000007f686c00 - 000000007fffffff NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default HPET: 3 timers in total, 0 timers will be used for per-cpu timer hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 comparators, 64-bit 14.318180 MHz counter Switching to clocksource tsc pnp: PnP ACPI init ACPI: bus type pnp registered pnp 00:00: [bus 00-ff] pnp 00:00: [io 0x0cf8-0x0cff] pnp 00:00: [io 0x0000-0x0cf7 window] pnp 00:00: [io 0x0d00-0xffff window] pnp 00:00: [mem 0x000a0000-0x000bffff window] pnp 00:00: [mem 0x000c0000-0x000effff window] pnp 00:00: [mem 0x000f0000-0x000fffff window] pnp 00:00: [mem 0x80000000-0xefffffff window] pnp 00:00: [mem 0xf4000000-0xfebfffff window] pnp 00:00: [mem 0xffa80800-0xffa80bff window] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active) pnp 00:01: [io 0x0060] pnp 00:01: [io 0x0064] pnp 00:01: [io 0x0062-0x0063] pnp 00:01: [io 0x0065-0x006f] pnp 00:01: [io 0x00e0-0x00ef] pnp 00:01: [io 0x0800-0x085f] pnp 00:01: [io 0x0c00-0x0c7f] pnp 00:01: [io 0x0860-0x08ff] pnp 00:01: disabling [io 0x0800-0x085f] because it overlaps 0000:00:1f.0 BAR 13 [io 0x0800-0x087f] pnp 00:01: disabling [io 0x0860-0x08ff] because it overlaps 0000:00:1f.0 BAR 13 [io 0x0800-0x087f] pnp 00:01: Plug and Play ACPI device, IDs PNP0c01 (active) pnp 00:02: [io 0x0080-0x009f] pnp 00:02: [io 0x0000-0x001f] pnp 00:02: [io 0x00c0-0x00df] pnp 00:02: [dma 4] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) pnp 00:03: [io 0x00f0-0x00ff] pnp 00:03: [irq 13] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active) pnp 00:04: [io 0x0061] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) pnp 00:05: [io 0x0070-0x007f] pnp 00:05: [irq 8] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active) pnp 00:06: [io 0x0378-0x037f] pnp 00:06: [io 0x0778-0x077f] pnp 00:06: [irq 7] pnp 00:06: [dma 0 disabled] pnp 00:06: Plug and Play ACPI device, IDs PNP0401 (active) pnp 00:07: [io 0x03f8-0x03ff] pnp 00:07: [irq 4] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active) pnp 00:08: [mem 0x00000000-0x0009ffff] pnp 00:08: [mem 0x00100000-0x00ffffff] pnp 00:08: [mem 0x01000000-0x7f686bff] pnp 00:08: [mem 0x000f0000-0x000fffff] pnp 00:08: [mem 0x000c0000-0x000cffff] pnp 00:08: [mem 0xfec00000-0xfecfffff] pnp 00:08: [mem 0xfee00000-0xfeefffff] pnp 00:08: [mem 0xfed20000-0xfed9ffff] pnp 00:08: [mem 0xffb00000-0xffbfffff] pnp 00:08: [mem 0xffc00000-0xffffffff] pnp 00:08: Plug and Play ACPI device, IDs PNP0c01 (active) pnp 00:09: [mem 0xf0000000-0xf3ffffff] pnp 00:09: [mem 0xfeda0000-0xfedacfff] pnp 00:09: [io 0x0100-0x01fe] pnp 00:09: [io 0x0200-0x0277] pnp 00:09: [io 0x0280-0x02e7] pnp 00:09: [io 0x02f0-0x02f7] pnp 00:09: [io 0x0300-0x0377] pnp 00:09: [io 0x0380-0x03bb] pnp 00:09: [io 0x03c0-0x03e7] pnp 00:09: [io 0x03f6-0x03f7] pnp 00:09: [io 0x0400-0x04cf] pnp 00:09: [io 0x04d2-0x057f] pnp 00:09: [io 0x0580-0x0677] pnp 00:09: [io 0x0680-0x0777] pnp 00:09: [io 0x0780-0x07bb] pnp 00:09: [io 0x07c0-0x07ff] pnp 00:09: [io 0x08e0-0x08ff] pnp 00:09: [io 0x0900-0x09fe] pnp 00:09: [io 0x0a00-0x0afe] pnp 00:09: [io 0x0b00-0x0bfe] pnp 00:09: [io 0x0c80-0x0caf] pnp 00:09: [io 0x0cb0-0x0cbf] pnp 00:09: [io 0x0cc0-0x0cf7] pnp 00:09: [io 0x0d00-0x0dfe] pnp 00:09: [io 0x0e00-0x0efe] pnp 00:09: [io 0x0f00-0x0ffe] pnp 00:09: [io 0x2000-0x20fe] pnp 00:09: [io 0x2100-0x21fe] pnp 00:09: [io 0x2200-0x22fe] pnp 00:09: [io 0x2300-0x23fe] pnp 00:09: [io 0x2400-0x24fe] pnp 00:09: [io 0x2500-0x25fe] pnp 00:09: [io 0x2600-0x26fe] pnp 00:09: [io 0x2700-0x27fe] pnp 00:09: [io 0x2800-0x28fe] pnp 00:09: [io 0x2900-0x29fe] pnp 00:09: [io 0x2a00-0x2afe] pnp 00:09: [io 0x2b00-0x2bfe] pnp 00:09: [io 0x2c00-0x2cfe] pnp 00:09: [io 0x2d00-0x2dfe] pnp 00:09: [io 0x2e00-0x2efe] pnp 00:09: [io 0x2f00-0x2ffe] pnp 00:09: [io 0x5000-0x50fe] pnp 00:09: [io 0x5100-0x51fe] pnp 00:09: [io 0x5200-0x52fe] pnp 00:09: [io 0x5300-0x53fe] pnp 00:09: [io 0x5400-0x54fe] pnp 00:09: [io 0x5500-0x55fe] pnp 00:09: [io 0x5600-0x56fe] pnp 00:09: [io 0x5700-0x57fe] pnp 00:09: [io 0x5800-0x58fe] pnp 00:09: [io 0x5900-0x59fe] pnp 00:09: [io 0x5a00-0x5afe] pnp 00:09: [io 0x5b00-0x5bfe] pnp 00:09: [io 0x5c00-0x5cfe] pnp 00:09: [io 0x5d00-0x5dfe] pnp 00:09: [io 0x5e00-0x5efe] pnp 00:09: [io 0x5f00-0x5ffe] pnp 00:09: [io 0x6000-0x60fe] pnp 00:09: [io 0x6100-0x61fe] pnp 00:09: [io 0x6200-0x62fe] pnp 00:09: [io 0x6300-0x63fe] pnp 00:09: [io 0x6400-0x64fe] pnp 00:09: [io 0x6500-0x65fe] pnp 00:09: [io 0x6600-0x66fe] pnp 00:09: [io 0x6700-0x67fe] pnp 00:09: [io 0x6800-0x68fe] pnp 00:09: [io 0x6900-0x69fe] pnp 00:09: [io 0x6a00-0x6afe] pnp 00:09: [io 0x6b00-0x6bfe] pnp 00:09: [io 0x6c00-0x6cfe] pnp 00:09: [io 0x6d00-0x6dfe] pnp 00:09: [io 0x6e00-0x6efe] pnp 00:09: [io 0x6f00-0x6ffe] pnp 00:09: [io 0xa000-0xa0fe] pnp 00:09: [io 0xa100-0xa1fe] pnp 00:09: [io 0xa200-0xa2fe] pnp 00:09: [io 0xa300-0xa3fe] pnp 00:09: [io 0xa400-0xa4fe] pnp 00:09: [io 0xa500-0xa5fe] pnp 00:09: [io 0xa600-0xa6fe] pnp 00:09: [io 0xa700-0xa7fe] pnp 00:09: [io 0xa800-0xa8fe] pnp 00:09: [io 0xa900-0xa9fe] pnp 00:09: [io 0xaa00-0xaafe] pnp 00:09: [io 0xab00-0xabfe] pnp 00:09: [io 0xac00-0xacfe] pnp 00:09: [io 0xad00-0xadfe] pnp 00:09: [io 0xae00-0xaefe] pnp 00:09: [io 0xaf00-0xaffe] pnp 00:09: Plug and Play ACPI device, IDs PNP0c02 (active) pnp: PnP ACPI: found 10 devices ACPI: ACPI bus type pnp unregistered system 00:01: [io 0x0c00-0x0c7f] has been reserved system 00:08: [mem 0x00000000-0x0009ffff] could not be reserved system 00:08: [mem 0x00100000-0x00ffffff] could not be reserved system 00:08: [mem 0x01000000-0x7f686bff] could not be reserved system 00:08: [mem 0x000f0000-0x000fffff] could not be reserved system 00:08: [mem 0x000c0000-0x000cffff] has been reserved system 00:08: [mem 0xfec00000-0xfecfffff] could not be reserved system 00:08: [mem 0xfee00000-0xfeefffff] has been reserved system 00:08: [mem 0xfed20000-0xfed9ffff] has been reserved system 00:08: [mem 0xffb00000-0xffbfffff] has been reserved system 00:08: [mem 0xffc00000-0xffffffff] has been reserved system 00:09: [io 0x0100-0x01fe] could not be reserved system 00:09: [io 0x0200-0x0277] has been reserved system 00:09: [io 0x0280-0x02e7] has been reserved system 00:09: [io 0x02f0-0x02f7] has been reserved system 00:09: [io 0x0300-0x0377] could not be reserved system 00:09: [io 0x0380-0x03bb] has been reserved system 00:09: [io 0x03c0-0x03e7] could not be reserved system 00:09: [io 0x03f6-0x03f7] could not be reserved system 00:09: [io 0x0400-0x04cf] has been reserved system 00:09: [io 0x04d2-0x057f] has been reserved system 00:09: [io 0x0580-0x0677] has been reserved system 00:09: [io 0x0680-0x0777] has been reserved system 00:09: [io 0x0780-0x07bb] has been reserved system 00:09: [io 0x07c0-0x07ff] has been reserved system 00:09: [io 0x08e0-0x08ff] has been reserved system 00:09: [io 0x0900-0x09fe] has been reserved system 00:09: [io 0x0a00-0x0afe] has been reserved system 00:09: [io 0x0b00-0x0bfe] has been reserved system 00:09: [io 0x0c80-0x0caf] has been reserved system 00:09: [io 0x0cb0-0x0cbf] has been reserved system 00:09: [io 0x0cc0-0x0cf7] has been reserved system 00:09: [io 0x0d00-0x0dfe] has been reserved system 00:09: [io 0x0e00-0x0efe] has been reserved system 00:09: [io 0x0f00-0x0ffe] has been reserved system 00:09: [io 0x2000-0x20fe] has been reserved system 00:09: [io 0x2100-0x21fe] has been reserved system 00:09: [io 0x2200-0x22fe] has been reserved system 00:09: [io 0x2300-0x23fe] has been reserved system 00:09: [io 0x2400-0x24fe] has been reserved system 00:09: [io 0x2500-0x25fe] has been reserved system 00:09: [io 0x2600-0x26fe] has been reserved system 00:09: [io 0x2700-0x27fe] has been reserved system 00:09: [io 0x2800-0x28fe] has been reserved system 00:09: [io 0x2900-0x29fe] has been reserved system 00:09: [io 0x2a00-0x2afe] has been reserved system 00:09: [io 0x2b00-0x2bfe] has been reserved system 00:09: [io 0x2c00-0x2cfe] has been reserved system 00:09: [io 0x2d00-0x2dfe] has been reserved system 00:09: [io 0x2e00-0x2efe] has been reserved system 00:09: [io 0x2f00-0x2ffe] has been reserved system 00:09: [io 0x5000-0x50fe] has been reserved system 00:09: [io 0x5100-0x51fe] has been reserved system 00:09: [io 0x5200-0x52fe] has been reserved system 00:09: [io 0x5300-0x53fe] has been reserved system 00:09: [io 0x5400-0x54fe] has been reserved system 00:09: [io 0x5500-0x55fe] has been reserved system 00:09: [io 0x5600-0x56fe] has been reserved system 00:09: [io 0x5700-0x57fe] has been reserved system 00:09: [io 0x5800-0x58fe] has been reserved system 00:09: [io 0x5900-0x59fe] has been reserved system 00:09: [io 0x5a00-0x5afe] has been reserved system 00:09: [io 0x5b00-0x5bfe] has been reserved system 00:09: [io 0x5c00-0x5cfe] has been reserved system 00:09: [io 0x5d00-0x5dfe] has been reserved system 00:09: [io 0x5e00-0x5efe] has been reserved system 00:09: [io 0x5f00-0x5ffe] has been reserved system 00:09: [io 0x6000-0x60fe] has been reserved system 00:09: [io 0x6100-0x61fe] has been reserved system 00:09: [io 0x6200-0x62fe] has been reserved system 00:09: [io 0x6300-0x63fe] has been reserved system 00:09: [io 0x6400-0x64fe] has been reserved system 00:09: [io 0x6500-0x65fe] has been reserved system 00:09: [io 0x6600-0x66fe] has been reserved system 00:09: [io 0x6700-0x67fe] has been reserved system 00:09: [io 0x6800-0x68fe] has been reserved system 00:09: [io 0x6900-0x69fe] has been reserved system 00:09: [io 0x6a00-0x6afe] has been reserved system 00:09: [io 0x6b00-0x6bfe] has been reserved system 00:09: [io 0x6c00-0x6cfe] has been reserved system 00:09: [io 0x6d00-0x6dfe] has been reserved system 00:09: [io 0x6e00-0x6efe] has been reserved system 00:09: [io 0x6f00-0x6ffe] has been reserved system 00:09: [io 0xa000-0xa0fe] has been reserved system 00:09: [io 0xa100-0xa1fe] has been reserved system 00:09: [io 0xa200-0xa2fe] has been reserved system 00:09: [io 0xa300-0xa3fe] has been reserved system 00:09: [io 0xa400-0xa4fe] has been reserved system 00:09: [io 0xa500-0xa5fe] has been reserved system 00:09: [io 0xa600-0xa6fe] has been reserved system 00:09: [io 0xa700-0xa7fe] has been reserved system 00:09: [io 0xa800-0xa8fe] has been reserved system 00:09: [io 0xa900-0xa9fe] has been reserved system 00:09: [io 0xaa00-0xaafe] has been reserved system 00:09: [io 0xab00-0xabfe] has been reserved system 00:09: [io 0xac00-0xacfe] has been reserved system 00:09: [io 0xad00-0xadfe] has been reserved system 00:09: [io 0xae00-0xaefe] has been reserved system 00:09: [io 0xaf00-0xaffe] has been reserved system 00:09: [mem 0xf0000000-0xf3ffffff] has been reserved system 00:09: [mem 0xfeda0000-0xfedacfff] has been reserved pci 0000:00:1c.0: BAR 15: assigned [mem 0xfffe00000-0xfffffffff 64bit pref] pci 0000:00:1c.1: BAR 15: assigned [mem 0xfffc00000-0xfffdfffff 64bit pref] pci 0000:00:1c.0: BAR 13: assigned [io 0xd000-0xdfff] pci 0000:00:1c.1: BAR 13: assigned [io 0xc000-0xcfff] pci 0000:00:01.0: PCI bridge to [bus 01-01] pci 0000:00:01.0: bridge window [io disabled] pci 0000:00:01.0: bridge window [mem 0xfe900000-0xfe9fffff] pci 0000:00:01.0: bridge window [mem pref disabled] pci 0000:00:1c.0: PCI bridge to [bus 02-02] pci 0000:00:1c.0: bridge window [io 0xd000-0xdfff] pci 0000:00:1c.0: bridge window [mem 0xfe800000-0xfe8fffff] pci 0000:00:1c.0: bridge window [mem 0xfffe00000-0xfffffffff 64bit pref] pci 0000:00:1c.1: PCI bridge to [bus 03-03] pci 0000:00:1c.1: bridge window [io 0xc000-0xcfff] pci 0000:00:1c.1: bridge window [mem 0xfe700000-0xfe7fffff] pci 0000:00:1c.1: bridge window [mem 0xfffc00000-0xfffdfffff 64bit pref] pci 0000:00:1e.0: PCI bridge to [bus 04-04] pci 0000:00:1e.0: bridge window [io disabled] pci 0000:00:1e.0: bridge window [mem disabled] pci 0000:00:1e.0: bridge window [mem pref disabled] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:01.0: setting latency timer to 64 pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:1c.0: setting latency timer to 64 pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 pci 0000:00:1c.1: setting latency timer to 64 pci 0000:00:1e.0: setting latency timer to 64 pci_bus 0000:00: resource 0 [io 0x0000-0xffff] pci_bus 0000:00: resource 1 [mem 0x00000000-0xfffffffff] pci_bus 0000:01: resource 1 [mem 0xfe900000-0xfe9fffff] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff] pci_bus 0000:02: resource 1 [mem 0xfe800000-0xfe8fffff] pci_bus 0000:02: resource 2 [mem 0xfffe00000-0xfffffffff 64bit pref] pci_bus 0000:03: resource 0 [io 0xc000-0xcfff] pci_bus 0000:03: resource 1 [mem 0xfe700000-0xfe7fffff] pci_bus 0000:03: resource 2 [mem 0xfffc00000-0xfffdfffff 64bit pref] pci_bus 0000:04: resource 4 [io 0x0000-0xffff] pci_bus 0000:04: resource 5 [mem 0x00000000-0xfffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 65536 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 10, 5242880 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered UDP hash table entries: 1024 (order: 5, 196608 bytes) UDP-Lite hash table entries: 1024 (order: 5, 196608 bytes) pci 0000:00:00.0: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:00.0: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:00.0: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:00.0: calling pci_fixup_video+0x0/0xf8 pci 0000:00:01.0: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:01.0: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:01.0: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:01.0: calling pci_fixup_video+0x0/0xf8 pci 0000:00:02.0: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:02.0: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:02.0: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:02.0: calling pci_fixup_video+0x0/0xf8 pci 0000:00:02.0: Boot video device pci 0000:00:02.1: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:02.1: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:02.1: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:02.1: calling pci_fixup_video+0x0/0xf8 pci 0000:00:1c.0: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:1c.0: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:1c.0: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:1c.0: calling pci_fixup_video+0x0/0xf8 pci 0000:00:1c.1: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:1c.1: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:1c.1: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:1c.1: calling pci_fixup_video+0x0/0xf8 pci 0000:00:1d.0: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:1d.0: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:1d.0: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0081 pci 0000:00:1d.0: Performing full reset pci 0000:00:1d.0: calling pci_fixup_video+0x0/0xf8 pci 0000:00:1d.1: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:1d.1: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:1d.1: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0081 pci 0000:00:1d.1: Performing full reset pci 0000:00:1d.1: calling pci_fixup_video+0x0/0xf8 pci 0000:00:1d.2: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:1d.2: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:1d.2: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0081 pci 0000:00:1d.2: Performing full reset pci 0000:00:1d.2: calling pci_fixup_video+0x0/0xf8 pci 0000:00:1d.3: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:1d.3: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:1d.3: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:1d.3: uhci_check_and_reset_hc: cmd = 0x0081 pci 0000:00:1d.3: Performing full reset pci 0000:00:1d.3: calling pci_fixup_video+0x0/0xf8 pci 0000:00:1d.7: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:1d.7: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:1d.7: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:1d.7: calling pci_fixup_video+0x0/0xf8 pci 0000:00:1e.0: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:1e.0: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:1e.0: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:1e.0: calling pci_fixup_video+0x0/0xf8 pci 0000:00:1e.2: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:1e.2: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:1e.2: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:1e.2: calling pci_fixup_video+0x0/0xf8 pci 0000:00:1f.0: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:1f.0: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:1f.0: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:1f.0: calling pci_fixup_video+0x0/0xf8 pci 0000:00:1f.1: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:1f.1: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:1f.1: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:1f.1: calling pci_fixup_video+0x0/0xf8 pci 0000:00:1f.2: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:1f.2: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:1f.2: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:1f.2: calling pci_fixup_video+0x0/0xf8 pci 0000:00:1f.3: calling quirk_e100_interrupt+0x0/0x1c9 pci 0000:00:1f.3: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:00:1f.3: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:00:1f.3: calling pci_fixup_video+0x0/0xf8 pci 0000:02:00.0: calling quirk_cardbus_legacy+0x0/0x35 pci 0000:02:00.0: calling quirk_usb_early_handoff+0x0/0x13a pci 0000:02:00.0: calling pci_fixup_video+0x0/0xf8 PCI: CLS 64 bytes, default 64 Unpacking initramfs... debug: unmapping init memory ffff880037be4000..ffff880037ff0000 DMA-API: preallocated 32768 debug entries DMA-API: debugging enabled by kernel config Simple Boot Flag at 0x7a set to 0x1 Scanning for low memory corruption every 60 seconds Initializing RT-Tester: OK audit: initializing netlink socket (disabled) type=2000 audit(1293538790.516:1): initialized Kprobe smoke test started Kprobe smoke test passed successfully HugeTLB registered 2 MB page size, pre-allocated 0 pages VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) msgmni has been set to 3930 cryptomgr_test used greatest stack depth: 6696 bytes left Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered (default) list_sort_test: start testing list_sort() ERST: Table is not found! Linux agpgart interface v0.103 [drm] Initialized drm 1.1.0 20060810 Fixed MDIO Bus: probed cpuidle: using governor ladder cpuidle: using governor menu registered taskstats version 1 IMA: No TPM chip found, activating TPM-bypass! hd: no drives specified - use hd=cyl,head,sectors on kernel command line Initalizing network drop monitor service debug: unmapping init memory ffffffff81c9b000..ffffffff81fa6000 Write protecting the kernel read-only data: 10240k Testing CPA: undo ffffffff81000000-ffffffff81a00000 Testing CPA: again debug: unmapping init memory ffff88000155c000..ffff880001600000 debug: unmapping init memory ffff8800018b4000..ffff880001a00000 modprobe used greatest stack depth: 5248 bytes left nash-hotplug (56): /proc/56/oom_adj is deprecated, please use /proc/56/oom_score_adj instead. input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0 ACPI: Power Button [VBTN] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 ACPI: Power Button [PWRF] agpgart-intel 0000:00:00.0: Intel 945G Chipset agpgart-intel 0000:00:00.0: detected gtt size: 262144K total, 262144K mappable agpgart-intel 0000:00:00.0: detected 8192K stolen memory agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000 i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 i915 0000:00:02.0: enabling bus mastering i915 0000:00:02.0: setting latency timer to 64 i2c i2c-0: adapter [i915 gmbus disabled] registered i2c i2c-1: adapter [i915 gmbus ssc] registered i2c i2c-2: adapter [i915 GPIOB] registered i2c i2c-3: adapter [i915 gmbus vga] registered i2c i2c-4: adapter [i915 GPIOA] registered i2c i2c-5: adapter [i915 gmbus panel] registered i2c i2c-6: adapter [i915 GPIOC] registered i2c i2c-7: adapter [i915 gmbus dpc] registered i2c i2c-8: adapter [i915 GPIOD] registered i2c i2c-9: adapter [i915 gmbus dpb] registered i2c i2c-10: adapter [i915 GPIOE] registered i2c i2c-11: adapter [i915 gmbus reserved] registered i2c i2c-12: adapter [i915 gmbus dpd] registered i2c i2c-13: adapter [i915 GPIOF] registered vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [drm] initialized overlay support No connectors reported connected with modes [drm] Cannot find any crtc or sizes - going 1024x768 fbcon: inteldrmfb (fb0) is primary device Console: switching to colour frame buffer device 128x48 fb0: inteldrmfb frame buffer device drm: registered panic notifier [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 modprobe used greatest stack depth: 4680 bytes left usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci_hcd: block sizes: qh 104 qtd 96 itd 192 sitd 96 ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 21 (level, low) -> IRQ 21 ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller /local/linsrc/linux-2.6.37-rc6/drivers/usb/core/inode.c: creating file 'devices' /local/linsrc/linux-2.6.37-rc6/drivers/usb/core/inode.c: creating file '001' ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered !ppc ports=8 ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr ehci_hcd 0000:00:1d.7: using broken periodic workaround ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: reset command 0000002 (park)=0 ithresh=0 period=1024 Reset HALT ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported ehci_hcd 0000:00:1d.7: supports USB remote wakeup ehci_hcd 0000:00:1d.7: irq 21, io mem 0xffa80800 ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT ehci_hcd 0000:00:1d.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 usb usb1: default language 0x0409 usb usb1: udev 1, busnum 1, minor = 0 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.37-rc6 ehci_hcd usb usb1: SerialNumber: 0000:00:1d.7 usb usb1: usb_probe_device usb usb1: configuration #1 chosen from 1 choice usb usb1: adding 1-0:1.0 (config #1, interface 0) hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: no power switching (usb 1.0) hub 1-0:1.0: individual port over-current protection hub 1-0:1.0: power on to power good time: 20ms hub 1-0:1.0: local power source is good hub 1-0:1.0: trying to enable port power on non-switchable hub /local/linsrc/linux-2.6.37-rc6/drivers/usb/core/inode.c: creating file '001' modprobe used greatest stack depth: 4432 bytes left ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci_hcd: block sizes: ed 80 td 96 uhci_hcd: USB Universal Host Controller Interface driver uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller /local/linsrc/linux-2.6.37-rc6/drivers/usb/core/inode.c: creating file '002' uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:1d.7: GetStatus port:3 status 001803 0 ACK POWER sig=j CSC CONNECT hub 1-0:1.0: port 3: status 0501 change 0001 uhci_hcd 0000:00:1d.0: detected 2 ports uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000 uhci_hcd 0000:00:1d.0: Performing full reset uhci_hcd 0000:00:1d.0: supports USB remote wakeup uhci_hcd 0000:00:1d.0: irq 21, io base 0x0000ff80 usb usb2: default language 0x0409 usb usb2: udev 1, busnum 2, minor = 128 usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: UHCI Host Controller usb usb2: Manufacturer: Linux 2.6.37-rc6 uhci_hcd usb usb2: SerialNumber: 0000:00:1d.0 usb usb2: usb_probe_device usb usb2: configuration #1 chosen from 1 choice usb usb2: adding 2-0:1.0 (config #1, interface 0) hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: individual port over-current protection hub 2-0:1.0: power on to power good time: 2ms hub 2-0:1.0: local power source is good hub 2-0:1.0: trying to enable port power on non-switchable hub /local/linsrc/linux-2.6.37-rc6/drivers/usb/core/inode.c: creating file '001' ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.0 uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22 uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller /local/linsrc/linux-2.6.37-rc6/drivers/usb/core/inode.c: creating file '003' uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: detected 2 ports uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000 uhci_hcd 0000:00:1d.1: Performing full reset uhci_hcd 0000:00:1d.1: supports USB remote wakeup uhci_hcd 0000:00:1d.1: irq 22, io base 0x0000ff60 usb usb3: default language 0x0409 usb usb3: udev 1, busnum 3, minor = 256 usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: UHCI Host Controller usb usb3: Manufacturer: Linux 2.6.37-rc6 uhci_hcd usb usb3: SerialNumber: 0000:00:1d.1 usb usb3: usb_probe_device usb usb3: configuration #1 chosen from 1 choice usb usb3: adding 3-0:1.0 (config #1, interface 0) hub 3-0:1.0: usb_probe_interface hub 3-0:1.0: usb_probe_interface - got id hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected hub 3-0:1.0: standalone hub hub 3-0:1.0: no power switching (usb 1.0) hub 3-0:1.0: individual port over-current protection hub 3-0:1.0: power on to power good time: 2ms hub 3-0:1.0: local power source is good hub 3-0:1.0: trying to enable port power on non-switchable hub /local/linsrc/linux-2.6.37-rc6/drivers/usb/core/inode.c: creating file '001' ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.1 uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller /local/linsrc/linux-2.6.37-rc6/drivers/usb/core/inode.c: creating file '004' uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: detected 2 ports uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000 uhci_hcd 0000:00:1d.2: Performing full reset uhci_hcd 0000:00:1d.2: supports USB remote wakeup uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ff40 usb usb4: default language 0x0409 usb usb4: udev 1, busnum 4, minor = 384 usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: UHCI Host Controller usb usb4: Manufacturer: Linux 2.6.37-rc6 uhci_hcd usb usb4: SerialNumber: 0000:00:1d.2 usb usb4: usb_probe_device usb usb4: configuration #1 chosen from 1 choice usb usb4: adding 4-0:1.0 (config #1, interface 0) hub 4-0:1.0: usb_probe_interface hub 4-0:1.0: usb_probe_interface - got id hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected hub 4-0:1.0: standalone hub hub 4-0:1.0: no power switching (usb 1.0) hub 4-0:1.0: individual port over-current protection hub 4-0:1.0: power on to power good time: 2ms hub 4-0:1.0: local power source is good hub 4-0:1.0: trying to enable port power on non-switchable hub /local/linsrc/linux-2.6.37-rc6/drivers/usb/core/inode.c: creating file '001' ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.2 uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23 uhci_hcd 0000:00:1d.3: setting latency timer to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller /local/linsrc/linux-2.6.37-rc6/drivers/usb/core/inode.c: creating file '005' uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.3: detected 2 ports uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd = 0x0000 uhci_hcd 0000:00:1d.3: Performing full reset uhci_hcd 0000:00:1d.3: supports USB remote wakeup uhci_hcd 0000:00:1d.3: irq 23, io base 0x0000ff20 usb usb5: default language 0x0409 usb usb5: udev 1, busnum 5, minor = 512 usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: UHCI Host Controller usb usb5: Manufacturer: Linux 2.6.37-rc6 uhci_hcd usb usb5: SerialNumber: 0000:00:1d.3 usb usb5: usb_probe_device usb usb5: configuration #1 chosen from 1 choice usb usb5: adding 5-0:1.0 (config #1, interface 0) hub 5-0:1.0: usb_probe_interface hub 5-0:1.0: usb_probe_interface - got id hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected hub 5-0:1.0: standalone hub hub 5-0:1.0: no power switching (usb 1.0) hub 5-0:1.0: individual port over-current protection hub 5-0:1.0: power on to power good time: 2ms hub 5-0:1.0: local power source is good hub 5-0:1.0: trying to enable port power on non-switchable hub /local/linsrc/linux-2.6.37-rc6/drivers/usb/core/inode.c: creating file '001' ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.3 hub 1-0:1.0: state 7 ports 8 chg 0008 evt 0000 hub 1-0:1.0: port 3, status 0501, change 0000, 480 Mb/s modprobe used greatest stack depth: 4344 bytes left uhci_hcd 0000:00:1d.1: port 1 portsc 008a,00 ehci_hcd 0000:00:1d.7: port 3 full speed --> companion ehci_hcd 0000:00:1d.7: GetStatus port:3 status 003801 0 ACK POWER OWNER sig=j CONNECT hub 1-0:1.0: port 3 not reset yet, waiting 50ms ata_piix 0000:00:1f.1: version 2.13 ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16 ata_piix 0000:00:1f.1: setting latency timer to 64 scsi0 : ata_piix scsi1 : ata_piix ehci_hcd 0000:00:1d.7: GetStatus port:3 status 003002 0 ACK POWER OWNER sig=se0 CSC ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000 hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0008 hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 ata_piix 0000:00:1f.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20 ata2: port disabled. ignoring. ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002 uhci_hcd 0000:00:1d.1: port 1 portsc 0093,00 hub 3-0:1.0: port 1, status 0101, change 0001, 12 Mb/s ata_piix 0000:00:1f.2: setting latency timer to 64 scsi2 : ata_piix ata1.00: ATAPI: HL-DT-STDVD+-RW GSA-H21N, A105, max UDMA/33 scsi3 : ata_piix ata3: SATA max UDMA/133 cmd 0xfe00 ctl 0xfe10 bmdma 0xfea0 irq 20 ata4: SATA max UDMA/133 cmd 0xfe20 ctl 0xfe30 bmdma 0xfea8 irq 20 hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 ata1.00: configured for UDMA/33 scsi 0:0:0:0: CD-ROM HL-DT-ST DVD+-RW GSA-H21N A105 PQ: 0 ANSI: 5 usb 3-1: new full speed USB device using uhci_hcd and address 2 ata3.00: ATA-7: WDC WD2500JS-75NCB3, 10.02E04, max UDMA/133 ata3.00: 488281250 sectors, multi 8: LBA48 NCQ (depth 0/32) ata3.00: configured for UDMA/133 scsi 2:0:0:0: Direct-Access ATA WDC WD2500JS-75N 10.0 PQ: 0 ANSI: 5 sd 2:0:0:0: [sda] 488281250 512-byte logical blocks: (250 GB/232 GiB) sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 > sd 2:0:0:0: [sda] Attached SCSI disk usb 3-1: ep0 maxpacket = 8 usb 3-1: default language 0x0409 usb 3-1: udev 2, busnum 3, minor = 257 usb 3-1: New USB device found, idVendor=413c, idProduct=1003 usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 3-1: Product: Dell USB Keyboard Hub usb 3-1: Manufacturer: Dell usb 3-1: usb_probe_device usb 3-1: configuration #1 chosen from 1 choice usb 3-1: adding 3-1:1.0 (config #1, interface 0) hub 3-1:1.0: usb_probe_interface hub 3-1:1.0: usb_probe_interface - got id hub 3-1:1.0: USB hub found hub 3-1:1.0: 3 ports detected hub 3-1:1.0: compound device; port removable status: FRR hub 3-1:1.0: individual port power switching hub 3-1:1.0: individual port over-current protection hub 3-1:1.0: power on to power good time: 44ms hub 3-1:1.0: hub controller current requirement: 100mA hub 3-1:1.0: 100mA bus power budget for each child hub 3-1:1.0: enabling power on all ports /local/linsrc/linux-2.6.37-rc6/drivers/usb/core/inode.c: creating file '002' hub 3-1:1.0: port 1: status 0101 change 0001 hub 3-1:1.0: port 3: status 0301 change 0001 uhci_hcd 0000:00:1d.1: reserve dev 2 ep81-INT, period 16, phase 8, 12 us hub 3-1:1.0: state 7 ports 3 chg 000a evt 0000 hub 3-1:1.0: port 1, status 0101, change 0000, 12 Mb/s usb 3-1.1: new full speed USB device using uhci_hcd and address 3 usb 3-1.1: ep0 maxpacket = 8 usb 3-1.1: skipped 1 descriptor after interface usb 3-1.1: skipped 1 descriptor after interface usb 3-1.1: default language 0x0409 usb 3-1.1: udev 3, busnum 3, minor = 258 usb 3-1.1: New USB device found, idVendor=413c, idProduct=2010 usb 3-1.1: New USB device strings: Mfr=1, Product=3, SerialNumber=0 usb 3-1.1: Product: Dell USB Keyboard usb 3-1.1: Manufacturer: Dell usb 3-1.1: usb_probe_device usb 3-1.1: configuration #1 chosen from 1 choice usb 3-1.1: adding 3-1.1:1.0 (config #1, interface 0) usb 3-1.1: adding 3-1.1:1.1 (config #1, interface 1) /local/linsrc/linux-2.6.37-rc6/drivers/usb/core/inode.c: creating file '003' hub 3-1:1.0: 350mA power budget left hub 3-1:1.0: port 3, status 0301, change 0000, 1.5 Mb/s usb usb2: suspend_rh (auto-stop) usb usb4: suspend_rh (auto-stop) usb usb5: suspend_rh (auto-stop) usb 3-1.3: new low speed USB device using uhci_hcd and address 4 usb 3-1.3: skipped 1 descriptor after interface usb 3-1.3: default language 0x0409 usb 3-1.3: udev 4, busnum 3, minor = 259 usb 3-1.3: New USB device found, idVendor=046d, idProduct=c016 usb 3-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 3-1.3: Product: Optical USB Mouse usb 3-1.3: Manufacturer: Logitech usb 3-1.3: usb_probe_device usb 3-1.3: configuration #1 chosen from 1 choice usb 3-1.3: adding 3-1.3:1.0 (config #1, interface 0) /local/linsrc/linux-2.6.37-rc6/drivers/usb/core/inode.c: creating file '004' hub 3-1:1.0: 250mA power budget left hub 3-1:1.0: state 7 ports 3 chg 0000 evt 0008 modprobe used greatest stack depth: 4192 bytes left Uniform Multi-Platform E-IDE driver EXT3-fs: barriers not enabled kjournald starting. Commit interval 5 seconds EXT3-fs (sda6): mounted filesystem with ordered data mode modprobe used greatest stack depth: 3368 bytes left NET: Registered protocol family 1 udev: starting version 141 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ACPI: acpi_idle registered with cpuidle shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled parport_pc 00:06: reported by Plug and Play ACPI parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A intel_rng: Firmware space is locked read-only. If you can't or intel_rng: don't want to disable this in firmware setup, and if intel_rng: you are certain that your system has a functional intel_rng: RNG, try using the 'no_fwh_detect' option. rtc_cmos 00:05: RTC can wake from S4 rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one day, 242 bytes nvram, hpet irqs i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17 i801_smbus 0000:00:1f.3: SMBus using interrupt SMI# i2c i2c-14: adapter [SMBus I801 adapter at e8a0] registered 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A input: PC Speaker as /devices/platform/pcspkr/input/input2 scsi 0:0:0:0: Attached scsi generic sg0 type 5 sd 2:0:0:0: Attached scsi generic sg1 type 0 iTCO_vendor_support: vendor-support=0 dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray cdrom: Uniform CD-ROM driver Revision: 3.20 sr 0:0:0:0: Attached scsi CD-ROM sr0 tg3.c:v3.115 (October 14, 2010) tg3 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 tg3 0000:02:00.0: setting latency timer to 64 iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06 iTCO_wdt: unable to reset NO_REBOOT flag, device disabled by hardware/BIOS tg3 0000:02:00.0: eth0: Tigon3 [partno(BCM5751PKFBG) rev 4001] (PCI Express) MAC address 00:18:8b:01:d2:2b tg3 0000:02:00.0: eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1]) tg3 0000:02:00.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] tg3 0000:02:00.0: eth0: dma_rwctrl[76180000] dma_mask[64-bit] leds_ss4200: no LED devices found usbhid 3-1.1:1.0: usb_probe_interface usbhid 3-1.1:1.0: usb_probe_interface - got id input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1.1/3-1.1:1.0/input/input3 uhci_hcd 0000:00:1d.1: reserve dev 3 ep81-INT, period 8, phase 4, 17 us generic-usb 0003:413C:2010.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.1-1.1/input0 usbhid 3-1.1:1.1: usb_probe_interface usbhid 3-1.1:1.1: usb_probe_interface - got id input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1.1/3-1.1:1.1/input/input4 uhci_hcd 0000:00:1d.1: reserve dev 3 ep82-INT, period 128, phase 0, 14 us generic-usb 0003:413C:2010.0002: input,hidraw1: USB HID v1.10 Device [Dell Dell USB Keyboard] on usb-0000:00:1d.1-1.1/input1 usbhid 3-1.3:1.0: usb_probe_interface usbhid 3-1.3:1.0: usb_probe_interface - got id input: Logitech Optical USB Mouse as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1.3/3-1.3:1.0/input/input5 generic-usb 0003:046D:C016.0003: input,hidraw2: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.1-1.3/input0 usbcore: registered new interface driver usbhid usbhid: USB HID core driver usbcore: registered new interface driver usbkbd usbkbd: :USB HID Boot Protocol keyboard driver usbcore: registered new interface driver usbmouse usbmouse: v1.6:USB HID Boot Protocol mouse driver Intel ICH 0000:00:1e.2: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Intel ICH 0000:00:1e.2: setting latency timer to 64 intel8x0: white list rate for 1028:01ad is 48000 ppdev: user-space parallel port driver mice: PS/2 mouse device common for all mice kvm: disabled by bios device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.18.0-ioctl (2010-06-29) initialised: dm-devel@redhat.com device-mapper: multipath: version 1.1.1 loaded EXT3-fs (sda6): using internal journal EXT3-fs: barriers not enabled kjournald starting. Commit interval 5 seconds EXT3-fs (sda1): using internal journal EXT3-fs (sda1): mounted filesystem with ordered data mode EXT3-fs: barriers not enabled kjournald starting. Commit interval 5 seconds EXT3-fs (sda3): using internal journal EXT3-fs (sda3): mounted filesystem with ordered data mode EXT3-fs: barriers not enabled kjournald starting. Commit interval 5 seconds EXT3-fs (sda5): using internal journal EXT3-fs (sda5): mounted filesystem with ordered data mode Adding 4194300k swap on /dev/sda2. Priority:-1 extents:1 across:4194300k microcode: CPU0 sig=0xf64, pf=0x4, revision=0x4 microcode: CPU1 sig=0xf64, pf=0x4, revision=0x4 microcode: Microcode Update Driver: v2.00 , Peter Oruba microcode: Microcode Update Driver: v2.00 removed. p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available NET: Registered protocol family 10 lo: Disabled Privacy Extensions ip6_tables: (C) 2000-2006 Netfilter Core Team nf_conntrack version 0.5.0 (16384 buckets, 65536 max) ip_tables: (C) 2000-2006 Netfilter Core Team CPA self-test: 4k 521862 large 0 gb 0 x 262144[ffff880000000000-ffff88003ffff000] miss 0 4k 521862 large 0 gb 0 x 262144[ffff880000000000-ffff88003ffff000] miss 0 4k 521862 large 0 gb 0 x 262144[ffff880000000000-ffff88003ffff000] miss 0 ok. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Bluetooth: Core ver 2.15 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.15 Bluetooth: L2CAP socket layer initialized Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bridge firewalling registered Bluetooth: SCO (Voice Link) ver 0.6 Bluetooth: SCO socket layer initialized Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period rpc.nfsd used greatest stack depth: 3288 bytes left uhci_hcd 0000:00:1d.1: reserve dev 4 ep81-INT, period 8, phase 4, 93 us ADDRCONF(NETDEV_UP): eth0: link is not ready lo: Disabled Privacy Extensions tg3 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex tg3 0000:02:00.0: eth0: Flow control is on for TX and on for RX ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready NET: Registered protocol family 17 virbr0: no IPv6 routers present eth0: no IPv6 routers present