[ 0.000000] Linux version 2.6.21-rc3-mm2 (rddunlap@unicorn) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #4 SMP Fri Mar 9 19:40:12 PST 2007 [ 0.000000] Command line: BOOT_IMAGE=lin2621-rc3mm2 ro root=308 resume=/dev/hda2 splash=silent showopts psmouse.proto=imps console=ttyS0,115200n8 console=tty0 netconsole=6503@192.168.0.107/eth0,6603@192.168.0.101/00:13:20:E3:97:02 debug ignore_loglevel acpi=off [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003ffc0000 (usable) [ 0.000000] BIOS-e820: 000000003ffc0000 - 000000003ffce000 (ACPI data) [ 0.000000] BIOS-e820: 000000003ffce000 - 000000003fff0000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] BIOS-e820: 00000000fecc0000 - 00000000fecc1000 (reserved) [ 0.000000] BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 262080) 1 entries of 256 used [ 0.000000] end_pfn_map = 1048576 [ 0.000000] DMI 2.3 present. [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 262080) 1 entries of 256 used [ 0.000000] sizeof(struct page) = 64 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1048576 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0 -> 159 [ 0.000000] 0: 256 -> 262080 [ 0.000000] On node 0 totalpages: 261983 [ 0.000000] Node 0 memmap at 0xffff810001000000 size 16777216 first pfn 0xffff810001000000 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 1576 pages reserved [ 0.000000] DMA zone: 2359 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 4031 pages used for memmap [ 0.000000] DMA32 zone: 253953 pages, LIFO batch:31 [ 0.000000] Normal zone: 0 pages used for memmap [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] Looks like a VIA chipset. Disabling IOMMU. Override with iommu=allowed [ 0.000000] Intel MultiProcessor Specification v1.4 [ 0.000000] MPTABLE: OEM ID: TEMPLATE MPTABLE: Product ID: ETEMPLATE MPTABLE: APIC at: 0xFEE00000 [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] I/O APIC #1 at 0xFEC00000. [ 0.000000] I/O APIC #2 at 0xFECC0000. [ 0.000000] Setting APIC routing to flat [ 0.000000] Processors: 1 [ 0.000000] Nosave address range: 000000000009f000 - 00000000000a0000 [ 0.000000] Nosave address range: 00000000000a0000 - 00000000000e8000 [ 0.000000] Nosave address range: 00000000000e8000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 37760 bytes of per cpu data [ 0.000000] Built 1 zonelists. Total pages: 256312 [ 0.000000] Kernel command line: BOOT_IMAGE=lin2621-rc3mm2 ro root=308 resume=/dev/hda2 splash=silent showopts psmouse.proto=imps console=ttyS0,115200n8 console=tty0 netconsole=6503@192.168.0.107/eth0,6603@192.168.0.101/00:13:20:E3:97:02 debug ignore_loglevel acpi=off [ 0.000000] netconsole: local port 6503 [ 0.000000] netconsole: local IP 192.168.0.107 [ 0.000000] netconsole: interface eth0 [ 0.000000] netconsole: remote port 6603 [ 0.000000] netconsole: remote IP 192.168.0.101 [ 0.000000] netconsole: remote ethernet address 00:13:20:e3:97:02 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 30.208184] time.c: Detected 2200.127 MHz processor. [ 30.208222] Console: colour dummy device 80x25 [ 30.589045] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 30.596929] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 30.612789] Memory: 1023452k/1048320k available (3343k kernel code, 24356k reserved, 1791k data, 224k init) [ 30.701746] Calibrating delay using timer specific routine.. 4405.40 BogoMIPS (lpj=8810809) [ 30.710170] Mount-cache hash table entries: 256 [ 30.714802] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 30.721934] CPU: L2 Cache: 512K (64 bytes/line) [ 30.726475] SMP alternatives: switching to UP code [ 30.731412] Freeing SMP alternatives: 28k freed [ 30.776914] Using local APIC timer interrupts. [ 30.826769] result 12500723 [ 30.829560] Detected 12.500 MHz APIC timer. [ 30.837677] Brought up 1 CPUs [ 30.841046] NET: Registered protocol family 16 [ 30.845507] ACPI Exception (utmutex-0263): AE_BAD_PARAMETER, Thread FFFF81003FFA14B0 could not acquire Mutex [1] [20070126] [ 30.856660] No dock devices found. [ 30.860134] PCI: Using configuration type 1 [ 30.865626] ACPI: Interpreter disabled. [ 30.869469] Linux Plug and Play Support v0.97 (c) Adam Belay [ 30.875134] pnp: PnP ACPI: disabled [ 30.878757] SCSI subsystem initialized [ 30.882587] usbcore: registered new interface driver usbfs [ 30.888121] usbcore: registered new interface driver hub [ 30.893479] usbcore: registered new device driver usb [ 30.898581] PCI: Probing PCI hardware [ 30.902243] PCI: Probing PCI hardware (bus 00) [ 30.907203] 0000:00:0f.0: cannot adjust BAR0 (not I/O) [ 30.912337] 0000:00:0f.0: cannot adjust BAR1 (not I/O) [ 30.917470] 0000:00:0f.0: cannot adjust BAR2 (not I/O) [ 30.922605] 0000:00:0f.0: cannot adjust BAR3 (not I/O) [ 30.928002] PCI: MSI-K8T-Neo2Fir, attempting to turn soundcard ON [ 30.934087] PCI: MSI-K8T-Neo2Fir, soundcard on [ 30.938817] Boot video device is 0000:02:00.0 [ 30.944740] PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0 [ 30.950861] PCI->APIC IRQ transform: 0000:00:02.0[A] -> IRQ 27 [ 30.956687] PCI->APIC IRQ transform: 0000:00:03.0[A] -> IRQ 31 [ 30.962515] PCI->APIC IRQ transform: 0000:00:03.1[B] -> IRQ 31 [ 30.968340] PCI->APIC IRQ transform: 0000:00:03.2[C] -> IRQ 39 [ 30.974168] PCI->APIC IRQ transform: 0000:00:03.3[D] -> IRQ 31 [ 30.979995] PCI->APIC IRQ transform: 0000:00:09.0[A] -> IRQ 18 [ 30.985822] PCI->APIC IRQ transform: 0000:00:0f.0[A] -> IRQ 20 [ 30.991650] PCI->APIC IRQ transform: 0000:00:10.0[A] -> IRQ 21 [ 30.997475] PCI->APIC IRQ transform: 0000:00:10.1[A] -> IRQ 21 [ 31.003374] PCI->APIC IRQ transform: 0000:00:10.2[B] -> IRQ 21 [ 31.009199] PCI->APIC IRQ transform: 0000:00:10.3[B] -> IRQ 21 [ 31.015026] PCI->APIC IRQ transform: 0000:00:10.4[C] -> IRQ 21 [ 31.020855] PCI->APIC IRQ transform: 0000:00:11.5[C] -> IRQ 22 [ 31.026682] PCI->APIC IRQ transform: 0000:00:12.0[A] -> IRQ 23 [ 31.032511] PCI->APIC IRQ transform: 0000:02:00.0[A] -> IRQ 24 [ 31.038481] agpgart: Detected AGP bridge 0 [ 31.045195] agpgart: AGP aperture is 64M @ 0xcc000000 [ 31.050583] PCI: Bridge: 0000:00:01.0 [ 31.054249] Time: tsc clocksource has been installed. [ 31.059311] IO window: disabled. [ 31.062711] MEM window: disabled. [ 31.066199] PREFETCH window: disabled. [ 31.070122] PCI: Bridge: 0000:00:02.0 [ 31.073783] IO window: c000-cfff [ 31.077186] MEM window: fea00000-feafffff [ 31.081369] PREFETCH window: b7f00000-c7efffff [ 31.085985] PCI: Bridge: 0000:00:03.0 [ 31.089644] IO window: disabled. [ 31.093049] MEM window: disabled. [ 31.096539] PREFETCH window: disabled. [ 31.100463] PCI: Bridge: 0000:00:03.1 [ 31.104121] IO window: disabled. [ 31.107528] MEM window: disabled. [ 31.111016] PREFETCH window: disabled. [ 31.114939] PCI: Bridge: 0000:00:03.2 [ 31.118598] IO window: disabled. [ 31.122004] MEM window: disabled. [ 31.125493] PREFETCH window: disabled. [ 31.129416] PCI: Bridge: 0000:00:03.3 [ 31.133073] IO window: disabled. [ 31.136473] MEM window: disabled. [ 31.139962] PREFETCH window: disabled. [ 31.143896] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 31.150166] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 31.156442] PCI: Setting latency timer of device 0000:00:03.0 to 64 [ 31.162710] PCI: Setting latency timer of device 0000:00:03.1 to 64 [ 31.168979] PCI: Setting latency timer of device 0000:00:03.2 to 64 [ 31.175249] PCI: Setting latency timer of device 0000:00:03.3 to 64 [ 31.181522] NET: Registered protocol family 2 [ 31.225295] IP route cache hash table entries: 32768 (order: 6, 262144 bytes) [ 31.232631] TCP established hash table entries: 65536 (order: 9, 2621440 bytes) [ 31.241048] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes) [ 31.248617] TCP: Hash tables configured (established 65536 bind 65536) [ 31.255244] TCP reno registered [ 31.269578] microcode: CPU0 not a capable Intel processor [ 31.274975] IA-32 Microcode Update Driver: v1.14a [ 31.282634] audit: initializing netlink socket (disabled) [ 31.288045] audit(1173470418.572:1): initialized [ 31.292725] Total HugeTLB memory allocated, 0 [ 31.297259] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 31.303771] io scheduler noop registered [ 31.307716] io scheduler anticipatory registered [ 31.312348] io scheduler deadline registered [ 31.316642] io scheduler cfq registered (default) [ 31.321660] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 31.327956] assign_interrupt_mode Found MSI capability [ 31.333090] Allocate Port Service[0000:00:02.0:pcie00] [ 31.338255] Allocate Port Service[0000:00:02.0:pcie02] [ 31.343471] PCI: Setting latency timer of device 0000:00:03.0 to 64 [ 31.349767] assign_interrupt_mode Found MSI capability [ 31.354898] Allocate Port Service[0000:00:03.0:pcie00] [ 31.360061] Allocate Port Service[0000:00:03.0:pcie02] [ 31.365270] PCI: Setting latency timer of device 0000:00:03.1 to 64 [ 31.371567] assign_interrupt_mode Found MSI capability [ 31.376700] Allocate Port Service[0000:00:03.1:pcie00] [ 31.381859] Allocate Port Service[0000:00:03.1:pcie02] [ 31.387066] PCI: Setting latency timer of device 0000:00:03.2 to 64 [ 31.393361] assign_interrupt_mode Found MSI capability [ 31.398494] Allocate Port Service[0000:00:03.2:pcie00] [ 31.403657] Allocate Port Service[0000:00:03.2:pcie02] [ 0.000000] Linux version 2.6.21-rc3-mm2 (rddunlap@unicorn) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #5 SMP Fri Mar 9 20:03:58 PST 2007 [ 0.000000] Command line: BOOT_IMAGE=lin2621-rc3mm2 ro root=308 resume=/dev/hda2 splash=silent showopts psmouse.proto=imps console=ttyS0,115200n8 console=tty0 netconsole=6503@192.168.0.107/eth0,6603@192.168.0.101/00:13:20:E3:97:02 debug ignore_loglevel [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003ffc0000 (usable) [ 0.000000] BIOS-e820: 000000003ffc0000 - 000000003ffce000 (ACPI data) [ 0.000000] BIOS-e820: 000000003ffce000 - 000000003fff0000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] BIOS-e820: 00000000fecc0000 - 00000000fecc1000 (reserved) [ 0.000000] BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 262080) 1 entries of 256 used [ 0.000000] end_pfn_map = 1048576 [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP 000F87C0, 0014 (r0 ACPIAM) [ 0.000000] ACPI: RSDT 3FFC0000, 0034 (r1 A M I OEMRSDT 9000528 MSFT 97) [ 0.000000] ACPI: FACP 3FFC0200, 0084 (r2 A M I OEMFACP 9000528 MSFT 97) [ 0.000000] ACPI: DSDT 3FFC0440, 45ED (r1 12345 12345123 123 INTL 2002026) [ 0.000000] ACPI: FACS 3FFCE000, 0040 [ 0.000000] ACPI: APIC 3FFC0390, 0068 (r1 A M I OEMAPIC 9000528 MSFT 97) [ 0.000000] ACPI: MCFG 3FFC0400, 003C (r1 A M I OEMMCFG 9000528 MSFT 97) [ 0.000000] ACPI: OEMB 3FFCE040, 0046 (r1 A M I AMI_OEM 9000528 MSFT 97) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 262080) 1 entries of 256 used [ 0.000000] sizeof(struct page) = 64 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1048576 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0 -> 159 [ 0.000000] 0: 256 -> 262080 [ 0.000000] On node 0 totalpages: 261983 [ 0.000000] Node 0 memmap at 0xffff810001000000 size 16777216 first pfn 0xffff810001000000 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 1572 pages reserved [ 0.000000] DMA zone: 2363 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 4031 pages used for memmap [ 0.000000] DMA32 zone: 253953 pages, LIFO batch:31 [ 0.000000] Normal zone: 0 pages used for memmap [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] Looks like a VIA chipset. Disabling IOMMU. Override with iommu=allowed [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfecc0000] gsi_base[24]) [ 0.000000] IOAPIC[1]: apic_id 2, address 0xfecc0000, GSI 24-47 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Setting APIC routing to flat [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Nosave address range: 000000000009f000 - 00000000000a0000 [ 0.000000] Nosave address range: 00000000000a0000 - 00000000000e8000 [ 0.000000] Nosave address range: 00000000000e8000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) [ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs [ 0.000000] PERCPU: Allocating 37760 bytes of per cpu data [ 0.000000] Built 1 zonelists. Total pages: 256316 [ 0.000000] Kernel command line: BOOT_IMAGE=lin2621-rc3mm2 ro root=308 resume=/dev/hda2 splash=silent showopts psmouse.proto=imps console=ttyS0,115200n8 console=tty0 netconsole=6503@192.168.0.107/eth0,6603@192.168.0.101/00:13:20:E3:97:02 debug ignore_loglevel [ 0.000000] netconsole: local port 6503 [ 0.000000] netconsole: local IP 192.168.0.107 [ 0.000000] netconsole: interface eth0 [ 0.000000] netconsole: remote port 6603 [ 0.000000] netconsole: remote IP 192.168.0.101 [ 0.000000] netconsole: remote ethernet address 00:13:20:e3:97:02 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 29.938665] time.c: Detected 2200.141 MHz processor. [ 29.938706] Console: colour dummy device 80x25 [ 30.422159] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 30.430046] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 30.445939] Memory: 1023468k/1048320k available (3336k kernel code, 24376k reserved, 1784k data, 224k init) [ 30.532139] Calibrating delay using timer specific routine.. 4405.43 BogoMIPS (lpj=8810872) [ 30.540557] Mount-cache hash table entries: 256 [ 30.545192] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 30.552320] CPU: L2 Cache: 512K (64 bytes/line) [ 30.556861] SMP alternatives: switching to UP code [ 30.561807] ACPI: Core revision 20070126 [ 30.608660] Using local APIC timer interrupts. [ 30.658513] result 12500823 [ 30.661305] Detected 12.500 MHz APIC timer. [ 30.668067] Brought up 1 CPUs [ 30.671399] NET: Registered protocol family 16 [ 30.675910] No dock devices found. [ 30.679382] ACPI: bus type pci registered [ 30.686014] PCI: Using MMCONFIG at e0000000 - efffffff [ 30.691187] PCI: No mmconfig possible on device 00:18 [ 30.702451] ACPI: Interpreter enabled [ 30.706119] ACPI: (supports S0 S1 S3 S4 S5) [ 30.710408] ACPI: Using IOAPIC for interrupt routing [ 30.724870] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 30.730117] 0000:00:0f.0: cannot adjust BAR0 (not I/O) [ 30.735269] 0000:00:0f.0: cannot adjust BAR1 (not I/O) [ 30.740423] 0000:00:0f.0: cannot adjust BAR2 (not I/O) [ 30.745632] 0000:00:0f.0: cannot adjust BAR3 (not I/O) [ 30.750983] PCI: MSI-K8T-Neo2Fir, attempting to turn soundcard ON [ 30.757070] PCI: MSI-K8T-Neo2Fir, soundcard on [ 30.761776] Boot video device is 0000:02:00.0 [ 30.766525] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 30.772646] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 30.779059] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBPG._PRT] [ 30.785483] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBP0._PRT] [ 30.791907] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBP1._PRT] [ 30.798322] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBP2._PRT] [ 30.804738] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBP3._PRT] [ 30.825538] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 30.832908] ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 10 11 12 14 15) [ 30.840256] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 30.847596] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 30.856110] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 30.864610] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 30.873122] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 30.881616] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14 15) [ 30.888930] Linux Plug and Play Support v0.97 (c) Adam Belay [ 30.894596] pnp: PnP ACPI init [ 30.902964] pnp: PnP ACPI: found 14 devices [ 30.907295] SCSI subsystem initialized [ 30.911123] usbcore: registered new interface driver usbfs [ 30.916645] usbcore: registered new interface driver hub [ 30.921988] usbcore: registered new device driver usb [ 30.927079] PCI: Using ACPI for IRQ routing [ 30.931264] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 30.939654] agpgart: Detected AGP bridge 0 [ 30.946335] agpgart: AGP aperture is 64M @ 0xcc000000 [ 30.951457] pnp: 00:08: ioport range 0xa00-0xa0f has been reserved [ 30.957626] Time: tsc clocksource has been installed. [ 30.962678] pnp: 00:08: ioport range 0x290-0x29f has been reserved [ 30.968847] pnp: 00:08: ioport range 0xa20-0xa2f has been reserved [ 30.975024] pnp: 00:08: ioport range 0xa30-0xa3f has been reserved [ 30.981195] pnp: 00:08: ioport range 0xa40-0xa4f has been reserved [ 30.987373] pnp: 00:09: iomem range 0xffb80000-0xffbfffff has been reserved [ 30.994323] pnp: 00:09: iomem range 0xfff00000-0xfff7fffe has been reserved [ 31.001290] pnp: 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved [ 31.008246] pnp: 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved [ 31.015200] pnp: 00:0c: iomem range 0xe0000000-0xefffffff has been reserved [ 31.022152] pnp: 00:0d: iomem range 0x0-0x9ffff could not be reserved [ 31.028583] pnp: 00:0d: iomem range 0xc0000-0xcffff has been reserved [ 31.035017] pnp: 00:0d: iomem range 0xe0000-0xfffff could not be reserved [ 31.041797] pnp: 00:0d: iomem range 0x100000-0x3fffffff could not be reserved [ 31.049187] PCI: Bridge: 0000:00:01.0 [ 31.052854] IO window: disabled. [ 31.056258] MEM window: disabled. [ 31.059745] PREFETCH window: disabled. [ 31.063668] PCI: Bridge: 0000:00:02.0 [ 31.067329] IO window: c000-cfff [ 31.070733] MEM window: fea00000-feafffff [ 31.074914] PREFETCH window: b7f00000-c7efffff [ 31.079530] PCI: Bridge: 0000:00:03.0 [ 31.083190] IO window: disabled. [ 31.086594] MEM window: disabled. [ 31.090085] PREFETCH window: disabled. [ 31.094005] PCI: Bridge: 0000:00:03.1 [ 31.097668] IO window: disabled. [ 31.101072] MEM window: disabled. [ 31.104560] PREFETCH window: disabled. [ 31.108483] PCI: Bridge: 0000:00:03.2 [ 0.000000] Linux version 2.6.21-rc3-mm2 (rddunlap@unicorn) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #5 SMP Fri Mar 9 20:03:58 PST 2007 [ 0.000000] Command line: BOOT_IMAGE=lin2621-rc3mm2 ro root=308 resume=/dev/hda2 splash=silent showopts psmouse.proto=imps console=ttyS0,115200n8 console=tty0 netconsole=6503@192.168.0.107/eth0,6603@192.168.0.101/00:13:20:E3:97:02 debug ignore_loglevel acpi=off [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003ffc0000 (usable) [ 0.000000] BIOS-e820: 000000003ffc0000 - 000000003ffce000 (ACPI data) [ 0.000000] BIOS-e820: 000000003ffce000 - 000000003fff0000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] BIOS-e820: 00000000fecc0000 - 00000000fecc1000 (reserved) [ 0.000000] BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 262080) 1 entries of 256 used [ 0.000000] end_pfn_map = 1048576 [ 0.000000] DMI 2.3 present. [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 262080) 1 entries of 256 used [ 0.000000] sizeof(struct page) = 64 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1048576 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0 -> 159 [ 0.000000] 0: 256 -> 262080 [ 0.000000] On node 0 totalpages: 261983 [ 0.000000] Node 0 memmap at 0xffff810001000000 size 16777216 first pfn 0xffff810001000000 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 1572 pages reserved [ 0.000000] DMA zone: 2363 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 4031 pages used for memmap [ 0.000000] DMA32 zone: 253953 pages, LIFO batch:31 [ 0.000000] Normal zone: 0 pages used for memmap [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] Looks like a VIA chipset. Disabling IOMMU. Override with iommu=allowed [ 0.000000] Intel MultiProcessor Specification v1.4 [ 0.000000] MPTABLE: OEM ID: TEMPLATE MPTABLE: Product ID: ETEMPLATE MPTABLE: APIC at: 0xFEE00000 [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] I/O APIC #1 at 0xFEC00000. [ 0.000000] I/O APIC #2 at 0xFECC0000. [ 0.000000] Setting APIC routing to flat [ 0.000000] Processors: 1 [ 0.000000] Nosave address range: 000000000009f000 - 00000000000a0000 [ 0.000000] Nosave address range: 00000000000a0000 - 00000000000e8000 [ 0.000000] Nosave address range: 00000000000e8000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 37760 bytes of per cpu data [ 0.000000] Built 1 zonelists. Total pages: 256316 [ 0.000000] Kernel command line: BOOT_IMAGE=lin2621-rc3mm2 ro root=308 resume=/dev/hda2 splash=silent showopts psmouse.proto=imps console=ttyS0,115200n8 console=tty0 netconsole=6503@192.168.0.107/eth0,6603@192.168.0.101/00:13:20:E3:97:02 debug ignore_loglevel acpi=off [ 0.000000] netconsole: local port 6503 [ 0.000000] netconsole: local IP 192.168.0.107 [ 0.000000] netconsole: interface eth0 [ 0.000000] netconsole: remote port 6603 [ 0.000000] netconsole: remote IP 192.168.0.101 [ 0.000000] netconsole: remote ethernet address 00:13:20:e3:97:02 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 30.597857] time.c: Detected 2200.123 MHz processor. [ 30.597896] Console: colour dummy device 80x25 [ 30.978773] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 30.986659] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 31.002544] Memory: 1023468k/1048320k available (3336k kernel code, 24340k reserved, 1784k data, 224k init) [ 31.091419] Calibrating delay using timer specific routine.. 4405.43 BogoMIPS (lpj=8810875) [ 31.099842] Mount-cache hash table entries: 256 [ 31.104474] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 31.111605] CPU: L2 Cache: 512K (64 bytes/line) [ 31.116147] SMP alternatives: switching to UP code [ 31.121084] Freeing SMP alternatives: 28k freed [ 31.166587] Using local APIC timer interrupts. [ 31.216440] result 12500700 [ 31.219230] Detected 12.500 MHz APIC timer. [ 31.227353] Brought up 1 CPUs [ 31.230729] NET: Registered protocol family 16 [ 31.235197] ACPI Exception (utmutex-0263): AE_BAD_PARAMETER, Thread FFFF81003FFA14B0 could not acquire Mutex [1] [20070126] [ 31.246349] No dock devices found. [ 31.249822] PCI: Using configuration type 1 [ 31.255295] ACPI: Interpreter disabled. [ 31.259131] Linux Plug and Play Support v0.97 (c) Adam Belay [ 31.264796] pnp: PnP ACPI: disabled [ 31.268417] SCSI subsystem initialized [ 31.272245] usbcore: registered new interface driver usbfs [ 31.277787] usbcore: registered new interface driver hub [ 31.283151] usbcore: registered new device driver usb [ 31.288249] PCI: Probing PCI hardware [ 31.291915] PCI: Probing PCI hardware (bus 00) [ 31.296878] 0000:00:0f.0: cannot adjust BAR0 (not I/O) [ 31.302008] 0000:00:0f.0: cannot adjust BAR1 (not I/O) [ 31.307143] 0000:00:0f.0: cannot adjust BAR2 (not I/O) [ 31.312278] 0000:00:0f.0: cannot adjust BAR3 (not I/O) [ 31.317673] PCI: MSI-K8T-Neo2Fir, attempting to turn soundcard ON [ 31.323761] PCI: MSI-K8T-Neo2Fir, soundcard on [ 31.328489] Boot video device is 0000:02:00.0 [ 31.334394] PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0 [ 31.340514] PCI->APIC IRQ transform: 0000:00:02.0[A] -> IRQ 27 [ 31.346342] PCI->APIC IRQ transform: 0000:00:03.0[A] -> IRQ 31 [ 31.352169] PCI->APIC IRQ transform: 0000:00:03.1[B] -> IRQ 31 [ 31.357995] PCI->APIC IRQ transform: 0000:00:03.2[C] -> IRQ 39 [ 31.363822] PCI->APIC IRQ transform: 0000:00:03.3[D] -> IRQ 31 [ 31.369649] PCI->APIC IRQ transform: 0000:00:09.0[A] -> IRQ 18 [ 31.375477] PCI->APIC IRQ transform: 0000:00:0f.0[A] -> IRQ 20 [ 31.381304] PCI->APIC IRQ transform: 0000:00:10.0[A] -> IRQ 21 [ 31.387131] PCI->APIC IRQ transform: 0000:00:10.1[A] -> IRQ 21 [ 31.392958] PCI->APIC IRQ transform: 0000:00:10.2[B] -> IRQ 21 [ 31.398785] PCI->APIC IRQ transform: 0000:00:10.3[B] -> IRQ 21 [ 31.404612] PCI->APIC IRQ transform: 0000:00:10.4[C] -> IRQ 21 [ 31.410441] PCI->APIC IRQ transform: 0000:00:11.5[C] -> IRQ 22 [ 31.416266] PCI->APIC IRQ transform: 0000:00:12.0[A] -> IRQ 23 [ 31.422095] PCI->APIC IRQ transform: 0000:02:00.0[A] -> IRQ 24 [ 31.428065] agpgart: Detected AGP bridge 0 [ 31.434964] agpgart: AGP aperture is 64M @ 0xcc000000 [ 31.440349] PCI: Bridge: 0000:00:01.0 [ 31.444008] Time: tsc clocksource has been installed. [ 31.449069] IO window: disabled. [ 31.452469] MEM window: disabled. [ 31.455957] PREFETCH window: disabled. [ 31.459880] PCI: Bridge: 0000:00:02.0 [ 31.463543] IO window: c000-cfff [ 31.466946] MEM window: fea00000-feafffff [ 31.471128] PREFETCH window: b7f00000-c7efffff [ 31.475743] PCI: Bridge: 0000:00:03.0 [ 31.479403] IO window: disabled. [ 31.482806] MEM window: disabled. [ 31.486297] PREFETCH window: disabled. [ 31.490220] PCI: Bridge: 0000:00:03.1 [ 31.493880] IO window: disabled. [ 31.497287] MEM window: disabled. [ 31.500775] PREFETCH window: disabled. [ 31.504698] PCI: Bridge: 0000:00:03.2 [ 31.508357] IO window: disabled. [ 31.511763] MEM window: disabled. [ 31.515251] PREFETCH window: disabled. [ 31.519175] PCI: Bridge: 0000:00:03.3 [ 31.522832] IO window: disabled. [ 31.526232] MEM window: disabled. [ 31.529720] PREFETCH window: disabled. [ 31.533654] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 31.539925] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 31.546200] PCI: Setting latency timer of device 0000:00:03.0 to 64 [ 31.552470] PCI: Setting latency timer of device 0000:00:03.1 to 64 [ 31.558747] PCI: Setting latency timer of device 0000:00:03.2 to 64 [ 31.565023] PCI: Setting latency timer of device 0000:00:03.3 to 64 [ 31.571299] NET: Registered protocol family 2 [ 31.614971] IP route cache hash table entries: 32768 (order: 6, 262144 bytes) [ 31.622303] TCP established hash table entries: 65536 (order: 9, 2621440 bytes) [ 31.630720] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes) [ 31.638302] TCP: Hash tables configured (established 65536 bind 65536) [ 31.644828] TCP reno registered [ 31.659259] microcode: CPU0 not a capable Intel processor [ 31.664655] IA-32 Microcode Update Driver: v1.14a [ 31.672319] audit: initializing netlink socket (disabled) [ 31.677729] audit(1173470841.572:1): initialized [ 31.682412] Total HugeTLB memory allocated, 0 [ 31.686949] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 31.693544] io scheduler noop registered [ 31.697483] io scheduler anticipatory registered [ 31.702117] io scheduler deadline registered [ 31.706401] io scheduler cfq registered (default) [ 31.711464] vesafb: framebuffer at 0xb8000000, mapped to 0xffffc20000080000, using 3072k, total 16384k [ 31.720763] vesafb: mode is 1024x768x16, linelength=2048, pages=9 [ 31.726846] vesafb: scrolling: redraw [ 31.730509] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 [ 31.749315] Console: switching to colour frame buffer device 128x48 [ 31.768824] fb0: VESA VGA frame buffer device [ 31.779437] Real Time Clock Driver v1.12ac [ 31.783729] Non-volatile memory driver v1.2 [ 31.788082] ppdev: user-space parallel port driver [ 31.793045] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0) [ 31.802492] Linux agpgart interface v0.102 (c) Dave Jones [ 31.808038] [drm] Initialized drm 1.1.0 20060810 [ 31.812788] Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds). [ 31.821974] Hangcheck: Using get_cycles(). [ 31.826216] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 31.834357] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 31.840954] parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] [ 31.981430] parport0: irq 7 detected [ 35.103686] floppy0: no floppy controllers found [ 35.108912] RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize [ 35.116716] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2 [ 35.122863] Copyright (c) 1999-2006 Intel Corporation. [ 35.128179] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI [ 35.134413] e100: Copyright(c) 1999-2006 Intel Corporation [ 35.140121] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker [ 35.151075] eth0: VIA Rhine II at 0xfebdf800, 00:14:2a:c9:24:d3, IRQ 23. [ 35.158799] eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1. [ 35.167109] tun: Universal TUN/TAP device driver, 1.6 [ 35.175550] tun: (C) 1999-2004 Max Krasnyansky [ 35.185273] netconsole: device eth0 not up yet, forcing it [ 35.194981] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 [ 35.205658] netconsole: carrier detect appears untrustworthy, waiting 4 seconds [ 41.175788] netconsole: network logging started [ 41.186378] Linux video capture interface: v2.00 [ 41.197012] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 41.209393] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 41.223631] Probing IDE interface ide0... [ 41.653714] hda: MAXTOR STM3200820A, ATA DISK drive [ 42.336913] Probing IDE interface ide1... [ 43.212255] hdc: TSSTcorpCD/DVDW SH-W162C, ATAPI CD/DVD-ROM drive [ 43.895475] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 43.906047] ide1 at 0x170-0x177,0x376 on irq 15 [ 43.916642] hda: max request size: 512KiB [ 43.969025] hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63 [ 43.993414] hda: cache flushes supported [ 44.003313] hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 > [ 44.101219] hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache [ 44.113890] Uniform CD-ROM driver Revision: 3.20 [ 44.127305] ehci_hcd 0000:00:10.4: EHCI Host Controller [ 44.138534] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1 [ 44.151961] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfebdfc00 [ 44.163578] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 44.177049] usb usb1: new device found, idVendor=0000, idProduct=0000 [ 44.189463] usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 44.202339] usb usb1: Product: EHCI Host Controller [ 44.213221] usb usb1: Manufacturer: Linux 2.6.21-rc3-mm2 ehci_hcd [ 44.225360] usb usb1: SerialNumber: 0000:00:10.4 [ 44.235988] usb usb1: configuration #1 chosen from 1 choice [ 44.247447] hub 1-0:1.0: USB hub found [ 44.257009] hub 1-0:1.0: 8 ports detected [ 44.371105] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 44.384384] USB Universal Host Controller Interface driver v3.0 [ 44.396061] uhci_hcd 0000:00:10.0: UHCI Host Controller [ 44.406987] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 [ 44.420091] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000ec00 [ 44.431531] usb usb2: new device found, idVendor=0000, idProduct=0000 [ 44.443676] usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 44.456221] usb usb2: Product: UHCI Host Controller [ 44.466690] usb usb2: Manufacturer: Linux 2.6.21-rc3-mm2 uhci_hcd [ 44.478380] usb usb2: SerialNumber: 0000:00:10.0 [ 44.488623] usb usb2: configuration #1 chosen from 1 choice [ 44.499768] hub 2-0:1.0: USB hub found [ 44.508986] hub 2-0:1.0: 2 ports detected [ 44.622863] uhci_hcd 0000:00:10.1: UHCI Host Controller [ 44.633482] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 [ 44.646244] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000e800 [ 44.657318] usb usb3: new device found, idVendor=0000, idProduct=0000 [ 44.669067] usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 44.681249] usb usb3: Product: UHCI Host Controller [ 44.691361] usb usb3: Manufacturer: Linux 2.6.21-rc3-mm2 uhci_hcd [ 44.702688] usb usb3: SerialNumber: 0000:00:10.1 [ 44.712823] usb usb3: configuration #1 chosen from 1 choice [ 44.723630] hub 3-0:1.0: USB hub found [ 44.732469] hub 3-0:1.0: 2 ports detected [ 44.774632] usb 1-7: new high speed USB device using ehci_hcd and address 2 [ 44.850647] uhci_hcd 0000:00:10.2: UHCI Host Controller [ 44.860986] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 [ 44.873494] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000e400 [ 44.884319] usb usb4: new device found, idVendor=0000, idProduct=0000 [ 44.895920] usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 44.907990] usb usb4: Product: UHCI Host Controller [ 44.917999] usb usb4: Manufacturer: Linux 2.6.21-rc3-mm2 uhci_hcd [ 44.929201] usb usb4: SerialNumber: 0000:00:10.2 [ 44.938990] usb usb4: configuration #1 chosen from 1 choice [ 44.949668] hub 4-0:1.0: USB hub found [ 44.958421] hub 4-0:1.0: 2 ports detected [ 44.969681] usb 1-7: new device found, idVendor=058f, idProduct=6362 [ 44.981056] usb 1-7: new device strings: Mfr=1, Product=2, SerialNumber=3 [ 44.992868] usb 1-7: Product: Mass Storage Device [ 45.002575] usb 1-7: Manufacturer: Generic [ 45.011580] usb 1-7: SerialNumber: 058F312D81B [ 45.020972] usb 1-7: configuration #1 chosen from 1 choice [ 45.090426] uhci_hcd 0000:00:10.3: UHCI Host Controller [ 45.100557] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5 [ 45.112877] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000e000 [ 45.123535] usb usb5: new device found, idVendor=0000, idProduct=0000 [ 45.134902] usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 45.146765] usb usb5: Product: UHCI Host Controller [ 45.156567] usb usb5: Manufacturer: Linux 2.6.21-rc3-mm2 uhci_hcd [ 45.167554] usb usb5: SerialNumber: 0000:00:10.3 [ 45.177088] usb usb5: configuration #1 chosen from 1 choice [ 45.187541] hub 5-0:1.0: USB hub found [ 45.196098] hub 5-0:1.0: 2 ports detected [ 46.109389] usbcore: registered new interface driver libusual [ 46.119965] usbcore: registered new interface driver hiddev [ 46.130239] usbcore: registered new interface driver usbhid [ 46.140417] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 46.151319] PNP: No PS/2 controller found. Probing ports directly. [ 46.162437] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 46.172076] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 46.181909] mice: PS/2 mouse device common for all mice [ 46.223884] input: AT Translated Set 2 keyboard as /class/input/input0 [ 46.243137] input: PC Speaker as /class/input/input1 [ 46.409116] input: ImPS/2 Generic Wheel Mouse as /class/input/input2 [ 46.424316] i2c /dev entries driver [ 46.432508] cpuidle: using governor ladder [ 46.441237] IPv4 over IPv4 tunneling driver [ 46.450083] GRE over IPv4 tunneling driver [ 46.458853] TCP cubic registered [ 0.000000] Linux version 2.6.21-rc3-mm2 (rddunlap@unicorn) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #5 SMP Fri Mar 9 20:03:58 PST 2007 [ 0.000000] Command line: BOOT_IMAGE=lin2621-rc3mm2 ro root=308 resume=/dev/hda2 splash=silent showopts psmouse.proto=imps console=ttyS0,115200n8 console=tty0 netconsole=6503@192.168.0.107/eth0,6603@192.168.0.101/00:13:20:E3:97:02 debug acpi=off ignore_loglevel [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003ffc0000 (usable) [ 0.000000] BIOS-e820: 000000003ffc0000 - 000000003ffce000 (ACPI data) [ 0.000000] BIOS-e820: 000000003ffce000 - 000000003fff0000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] BIOS-e820: 00000000fecc0000 - 00000000fecc1000 (reserved) [ 0.000000] BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 262080) 1 entries of 256 used [ 0.000000] end_pfn_map = 1048576 [ 0.000000] DMI 2.3 present. [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 262080) 1 entries of 256 used [ 0.000000] sizeof(struct page) = 64 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1048576 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0 -> 159 [ 0.000000] 0: 256 -> 262080 [ 0.000000] On node 0 totalpages: 261983 [ 0.000000] Node 0 memmap at 0xffff810001000000 size 16777216 first pfn 0xffff810001000000 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 1572 pages reserved [ 0.000000] DMA zone: 2363 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 4031 pages used for memmap [ 0.000000] DMA32 zone: 253953 pages, LIFO batch:31 [ 0.000000] Normal zone: 0 pages used for memmap [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] Looks like a VIA chipset. Disabling IOMMU. Override with iommu=allowed [ 0.000000] Intel MultiProcessor Specification v1.4 [ 0.000000] MPTABLE: OEM ID: TEMPLATE MPTABLE: Product ID: ETEMPLATE MPTABLE: APIC at: 0xFEE00000 [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] I/O APIC #1 at 0xFEC00000. [ 0.000000] I/O APIC #2 at 0xFECC0000. [ 0.000000] Setting APIC routing to flat [ 0.000000] Processors: 1 [ 0.000000] Nosave address range: 000000000009f000 - 00000000000a0000 [ 0.000000] Nosave address range: 00000000000a0000 - 00000000000e8000 [ 0.000000] Nosave address range: 00000000000e8000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 37760 bytes of per cpu data [ 0.000000] Built 1 zonelists. Total pages: 256316 [ 0.000000] Kernel command line: BOOT_IMAGE=lin2621-rc3mm2 ro root=308 resume=/dev/hda2 splash=silent showopts psmouse.proto=imps console=ttyS0,115200n8 console=tty0 netconsole=6503@192.168.0.107/eth0,6603@192.168.0.101/00:13:20:E3:97:02 debug acpi=off ignore_loglevel [ 0.000000] netconsole: local port 6503 [ 0.000000] netconsole: local IP 192.168.0.107 [ 0.000000] netconsole: interface eth0 [ 0.000000] netconsole: remote port 6603 [ 0.000000] netconsole: remote IP 192.168.0.101 [ 0.000000] netconsole: remote ethernet address 00:13:20:e3:97:02 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 30.929698] time.c: Detected 2200.124 MHz processor. [ 30.929738] Console: colour dummy device 80x25 [ 31.310524] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 31.318408] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 31.334289] Memory: 1023468k/1048320k available (3336k kernel code, 24340k reserved, 1784k data, 224k init) [ 31.423260] Calibrating delay using timer specific routine.. 4405.36 BogoMIPS (lpj=8810728) [ 31.431670] Mount-cache hash table entries: 256 [ 31.436321] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 31.443450] CPU: L2 Cache: 512K (64 bytes/line) [ 31.447992] SMP alternatives: switching to UP code [ 31.452928] Freeing SMP alternatives: 28k freed [ 31.498432] Using local APIC timer interrupts. [ 31.548287] result 12500706 [ 31.551077] Detected 12.500 MHz APIC timer. [ 31.559186] Brought up 1 CPUs [ 31.562556] NET: Registered protocol family 16 [ 31.567024] ACPI Exception (utmutex-0263): AE_BAD_PARAMETER, Thread FFFF81003FFA14B0 could not acquire Mutex [1] [20070126] [ 31.578179] No dock devices found. [ 31.581651] PCI: Using configuration type 1 [ 31.587127] ACPI: Interpreter disabled. [ 31.590968] Linux Plug and Play Support v0.97 (c) Adam Belay [ 31.596633] pnp: PnP ACPI: disabled [ 31.600254] SCSI subsystem initialized [ 31.604083] usbcore: registered new interface driver usbfs [ 31.609624] usbcore: registered new interface driver hub [ 31.614988] usbcore: registered new device driver usb [ 31.620086] PCI: Probing PCI hardware [ 31.623752] PCI: Probing PCI hardware (bus 00) [ 31.628715] 0000:00:0f.0: cannot adjust BAR0 (not I/O) [ 31.633845] 0000:00:0f.0: cannot adjust BAR1 (not I/O) [ 31.638980] 0000:00:0f.0: cannot adjust BAR2 (not I/O) [ 31.644114] 0000:00:0f.0: cannot adjust BAR3 (not I/O) [ 31.649511] PCI: MSI-K8T-Neo2Fir, attempting to turn soundcard ON [ 31.655596] PCI: MSI-K8T-Neo2Fir, soundcard on [ 31.660324] Boot video device is 0000:02:00.0 [ 31.666236] PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0 [ 31.672350] PCI->APIC IRQ transform: 0000:00:02.0[A] -> IRQ 27 [ 31.678178] PCI->APIC IRQ transform: 0000:00:03.0[A] -> IRQ 31 [ 31.684005] PCI->APIC IRQ transform: 0000:00:03.1[B] -> IRQ 31 [ 31.689903] PCI->APIC IRQ transform: 0000:00:03.2[C] -> IRQ 39 [ 31.695728] PCI->APIC IRQ transform: 0000:00:03.3[D] -> IRQ 31 [ 31.701556] PCI->APIC IRQ transform: 0000:00:09.0[A] -> IRQ 18 [ 31.707383] PCI->APIC IRQ transform: 0000:00:0f.0[A] -> IRQ 20 [ 31.713210] PCI->APIC IRQ transform: 0000:00:10.0[A] -> IRQ 21 [ 31.719037] PCI->APIC IRQ transform: 0000:00:10.1[A] -> IRQ 21 [ 31.724865] PCI->APIC IRQ transform: 0000:00:10.2[B] -> IRQ 21 [ 31.730692] PCI->APIC IRQ transform: 0000:00:10.3[B] -> IRQ 21 [ 31.736519] PCI->APIC IRQ transform: 0000:00:10.4[C] -> IRQ 21 [ 31.742347] PCI->APIC IRQ transform: 0000:00:11.5[C] -> IRQ 22 [ 31.748172] PCI->APIC IRQ transform: 0000:00:12.0[A] -> IRQ 23 [ 31.754001] PCI->APIC IRQ transform: 0000:02:00.0[A] -> IRQ 24 [ 31.759973] agpgart: Detected AGP bridge 0 [ 31.766691] agpgart: AGP aperture is 64M @ 0xcc000000 [ 31.772070] PCI: Bridge: 0000:00:01.0 [ 31.775733] Time: tsc clocksource has been installed. [ 31.780794] IO window: disabled. [ 31.784194] MEM window: disabled. [ 31.787682] PREFETCH window: disabled. [ 31.791605] PCI: Bridge: 0000:00:02.0 [ 31.795266] IO window: c000-cfff [ 31.798669] MEM window: fea00000-feafffff [ 31.802853] PREFETCH window: b7f00000-c7efffff [ 31.807468] PCI: Bridge: 0000:00:03.0 [ 31.811128] IO window: disabled. [ 31.814531] MEM window: disabled. [ 31.818021] PREFETCH window: disabled. [ 31.821945] PCI: Bridge: 0000:00:03.1 [ 31.825605] IO window: disabled. [ 31.829009] MEM window: disabled. [ 31.832498] PREFETCH window: disabled. [ 31.836421] PCI: Bridge: 0000:00:03.2 [ 31.840082] IO window: disabled. [ 31.843488] MEM window: disabled. [ 31.846976] PREFETCH window: disabled. [ 31.850899] PCI: Bridge: 0000:00:03.3 [ 31.854557] IO window: disabled. [ 31.857965] MEM window: disabled. [ 31.861453] PREFETCH window: disabled. [ 31.865388] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 31.871658] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 31.877933] PCI: Setting latency timer of device 0000:00:03.0 to 64 [ 31.884203] PCI: Setting latency timer of device 0000:00:03.1 to 64 [ 31.890480] PCI: Setting latency timer of device 0000:00:03.2 to 64 [ 31.896756] PCI: Setting latency timer of device 0000:00:03.3 to 64 [ 31.903032] NET: Registered protocol family 2 [ 31.946806] IP route cache hash table entries: 32768 (order: 6, 262144 bytes) [ 31.954139] TCP established hash table entries: 65536 (order: 9, 2621440 bytes) [ 31.962554] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes) [ 31.970142] TCP: Hash tables configured (established 65536 bind 65536) [ 31.976664] TCP reno registered [ 31.991093] microcode: CPU0 not a capable Intel processor [ 31.996491] IA-32 Microcode Update Driver: v1.14a [ 32.004155] audit: initializing netlink socket (disabled) [ 32.009557] audit(1173470964.572:1): initialized [ 32.014240] Total HugeTLB memory allocated, 0 [ 32.018778] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 32.025294] io scheduler noop registered [ 32.029233] io scheduler anticipatory registered [ 32.033867] io scheduler deadline registered [ 32.038151] io scheduler cfq registered (default) [ 32.043217] vesafb: framebuffer at 0xb8000000, mapped to 0xffffc20000080000, using 3072k, total 16384k [ 32.052513] vesafb: mode is 1024x768x16, linelength=2048, pages=9 [ 32.058596] vesafb: scrolling: redraw [ 32.062260] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 [ 32.081065] Console: switching to colour frame buffer device 128x48 [ 32.100574] fb0: VESA VGA frame buffer device [ 32.111184] Real Time Clock Driver v1.12ac [ 32.115478] Non-volatile memory driver v1.2 [ 32.119830] ppdev: user-space parallel port driver [ 32.124786] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0) [ 32.134233] Linux agpgart interface v0.102 (c) Dave Jones [ 32.139781] [drm] Initialized drm 1.1.0 20060810 [ 32.144529] Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds). [ 32.153717] Hangcheck: Using get_cycles(). [ 32.157959] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 32.166100] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 32.172707] parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] [ 32.313269] parport0: irq 7 detected [ 35.435519] floppy0: no floppy controllers found [ 35.440750] RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize [ 35.448554] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2 [ 35.454701] Copyright (c) 1999-2006 Intel Corporation. [ 35.460017] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI [ 35.466251] e100: Copyright(c) 1999-2006 Intel Corporation [ 35.471958] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker [ 35.482913] eth0: VIA Rhine II at 0xfebdf800, 00:14:2a:c9:24:d3, IRQ 23. [ 35.490618] eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1. [ 35.498929] tun: Universal TUN/TAP device driver, 1.6 [ 35.507361] tun: (C) 1999-2004 Max Krasnyansky [ 35.517085] netconsole: device eth0 not up yet, forcing it [ 35.526782] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 [ 35.537454] netconsole: carrier detect appears untrustworthy, waiting 4 seconds [ 41.506016] netconsole: network logging started [ 41.516597] Linux video capture interface: v2.00 [ 41.527221] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 41.539594] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 41.553816] Probing IDE interface ide0... [ 41.981551] hda: MAXTOR STM3200820A, ATA DISK drive [ 42.664750] Probing IDE interface ide1... [ 43.540092] hdc: TSSTcorpCD/DVDW SH-W162C, ATAPI CD/DVD-ROM drive [ 44.223312] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 44.233876] ide1 at 0x170-0x177,0x376 on irq 15 [ 44.244463] hda: max request size: 512KiB [ 44.300878] hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63 [ 44.325267] hda: cache flushes supported [ 44.335158] hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 > [ 44.433401] hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache [ 44.446064] Uniform CD-ROM driver Revision: 3.20 [ 44.459488] ehci_hcd 0000:00:10.4: EHCI Host Controller [ 44.470706] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1 [ 44.484132] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfebdfc00 [ 44.495744] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 44.509216] usb usb1: new device found, idVendor=0000, idProduct=0000 [ 44.521620] usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 44.534494] usb usb1: Product: EHCI Host Controller [ 44.545370] usb usb1: Manufacturer: Linux 2.6.21-rc3-mm2 ehci_hcd [ 44.557508] usb usb1: SerialNumber: 0000:00:10.4 [ 44.568141] usb usb1: configuration #1 chosen from 1 choice [ 44.579596] hub 1-0:1.0: USB hub found [ 44.589159] hub 1-0:1.0: 8 ports detected [ 44.702938] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 44.716220] USB Universal Host Controller Interface driver v3.0 [ 44.727900] uhci_hcd 0000:00:10.0: UHCI Host Controller [ 44.738833] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 [ 44.751938] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000ec00 [ 44.763369] usb usb2: new device found, idVendor=0000, idProduct=0000 [ 44.775522] usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 44.788069] usb usb2: Product: UHCI Host Controller [ 44.798544] usb usb2: Manufacturer: Linux 2.6.21-rc3-mm2 uhci_hcd [ 44.810233] usb usb2: SerialNumber: 0000:00:10.0 [ 44.820485] usb usb2: configuration #1 chosen from 1 choice [ 44.831639] hub 2-0:1.0: USB hub found [ 44.840866] hub 2-0:1.0: 2 ports detected [ 44.954696] uhci_hcd 0000:00:10.1: UHCI Host Controller [ 44.965327] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 [ 44.978089] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000e800 [ 44.989163] usb usb3: new device found, idVendor=0000, idProduct=0000 [ 45.000920] usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 45.013111] usb usb3: Product: UHCI Host Controller [ 45.023234] usb usb3: Manufacturer: Linux 2.6.21-rc3-mm2 uhci_hcd [ 45.034566] usb usb3: SerialNumber: 0000:00:10.1 [ 45.044739] usb usb3: configuration #1 chosen from 1 choice [ 45.055551] hub 3-0:1.0: USB hub found [ 45.064402] hub 3-0:1.0: 2 ports detected [ 45.106465] usb 1-7: new high speed USB device using ehci_hcd and address 2 [ 45.182481] uhci_hcd 0000:00:10.2: UHCI Host Controller [ 45.192831] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 [ 45.205349] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000e400 [ 45.216173] usb usb4: new device found, idVendor=0000, idProduct=0000 [ 45.227782] usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 45.239852] usb usb4: Product: UHCI Host Controller [ 45.249862] usb usb4: Manufacturer: Linux 2.6.21-rc3-mm2 uhci_hcd [ 45.261073] usb usb4: SerialNumber: 0000:00:10.2 [ 45.270860] usb usb4: configuration #1 chosen from 1 choice [ 45.281539] hub 4-0:1.0: USB hub found [ 45.290295] hub 4-0:1.0: 2 ports detected [ 45.301348] usb 1-7: new device found, idVendor=058f, idProduct=6362 [ 45.312738] usb 1-7: new device strings: Mfr=1, Product=2, SerialNumber=3 [ 45.324559] usb 1-7: Product: Mass Storage Device [ 45.334272] usb 1-7: Manufacturer: Generic [ 45.343277] usb 1-7: SerialNumber: 058F312D81B [ 45.352663] usb 1-7: configuration #1 chosen from 1 choice [ 45.422259] uhci_hcd 0000:00:10.3: UHCI Host Controller [ 45.432386] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5 [ 45.444704] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000e000 [ 45.455364] usb usb5: new device found, idVendor=0000, idProduct=0000 [ 45.466723] usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1 [ 45.478584] usb usb5: Product: UHCI Host Controller [ 45.488377] usb usb5: Manufacturer: Linux 2.6.21-rc3-mm2 uhci_hcd [ 45.499356] usb usb5: SerialNumber: 0000:00:10.3 [ 45.508882] usb usb5: configuration #1 chosen from 1 choice [ 45.519333] hub 5-0:1.0: USB hub found [ 45.527891] hub 5-0:1.0: 2 ports detected [ 46.441222] usbcore: registered new interface driver libusual [ 46.451802] usbcore: registered new interface driver hiddev [ 46.462084] usbcore: registered new interface driver usbhid [ 46.472265] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 46.483164] PNP: No PS/2 controller found. Probing ports directly. [ 46.494281] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 46.503922] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 46.513764] mice: PS/2 mouse device common for all mice [ 46.555547] input: AT Translated Set 2 keyboard as /class/input/input0 [ 46.577098] input: PC Speaker as /class/input/input1 [ 46.742811] input: ImPS/2 Generic Wheel Mouse as /class/input/input2 [ 46.758013] i2c /dev entries driver [ 46.766212] cpuidle: using governor ladder [ 46.774947] IPv4 over IPv4 tunneling driver [ 46.783796] GRE over IPv4 tunneling driver [ 46.792610] TCP cubic registered [ 46.800388] NET: Registered protocol family 1 [ 46.809304] NET: Registered protocol family 17 [ 46.818265] NET: Registered protocol family 15 [ 46.827143] ieee80211: 802.11 data/management/control stack, git-1.1.13 [ 46.838213] ieee80211: Copyright (C) 2004-2005 Intel Corporation [ 46.851115] ieee80211_crypt: registered algorithm 'NULL' [ 46.860967] ieee80211_crypt: registered algorithm 'WEP' [ 46.870622] ieee80211_crypt: registered algorithm 'CCMP' [ 46.880297] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3500+ processors (version 2.00.00) [ 46.899590] powernow-k8: 0 : fid 0x2 (1000 MHz), vid 0x12 [ 46.909732] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa [ 46.919716] powernow-k8: 2 : fid 0xc (2000 MHz), vid 0x8 [ 46.929628] powernow-k8: 3 : fid 0xe (2200 MHz), vid 0x8 [ 46.958206] BIOS EDD facility v0.16 2004-Jun-25, 1 devices found [ 47.005726] kjournald starting. Commit interval 5 seconds [ 47.015553] EXT3-fs: mounted filesystem with ordered data mode. [ 47.025867] VFS: Mounted root (ext3 filesystem) readonly. [ 47.035643] Freeing unused kernel memory: 224k freed [ 47.045108] Write protecting the kernel read-only data: 1345k [ 50.176096] lp0: using parport0 (polling). [ 50.184409] lp0: console ready [ 52.416155] PCI: Setting latency timer of device 0000:00:11.5 to 64 [ 53.611750] Adding 2097136k swap on /dev/hda2. Priority:-1 extents:1 across:2097136k [ 53.708835] EXT3 (no)acl options not supported [ 54.385301] EXT3 (no)acl options not supported [ 54.395938] EXT3 FS on hda8, internal journal [ 57.730274] loop: loaded (max 8 devices) [ 57.751261] EXT3 (no)acl options not supported [ 57.850672] kjournald starting. Commit interval 5 seconds [ 57.862435] EXT3 FS on hda1, internal journal [ 57.871728] EXT3-fs: mounted filesystem with ordered data mode. [ 57.901711] EXT3 (no)acl options not supported [ 57.930490] kjournald starting. Commit interval 5 seconds [ 57.951774] EXT3 FS on hda5, internal journal [ 57.960903] EXT3-fs: mounted filesystem with ordered data mode. [ 57.990263] EXT3 (no)acl options not supported [ 58.019414] kjournald starting. Commit interval 5 seconds [ 58.039711] EXT3 FS on hda6, internal journal [ 58.048874] EXT3-fs: mounted filesystem with ordered data mode. [ 85.053157] Marking TSC unstable due to cpufreq changes [ 85.056131] Time: jiffies clocksource has been installed. [ 0.000000] Linux version 2.6.21-rc3 (rddunlap@unicorn) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #3 SMP Fri Mar 9 20:14:58 PST 2007 [ 0.000000] Command line: BOOT_IMAGE=lin2621-rc3 ro root=308 resume=/dev/hda2 splash=silent showopts psmouse.proto=imps console=ttyS0,115200n8 console=tty0 netconsole=6503@192.168.0.107/eth0,6603@192.168.0.101/00:13:20:E3:97:02 debug [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003ffc0000 (usable) [ 0.000000] BIOS-e820: 000000003ffc0000 - 000000003ffce000 (ACPI data) [ 0.000000] BIOS-e820: 000000003ffce000 - 000000003fff0000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] BIOS-e820: 00000000fecc0000 - 00000000fecc1000 (reserved) [ 0.000000] BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 262080) 1 entries of 256 used [ 0.000000] end_pfn_map = 1048576 [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP 000F87C0, 0014 (r0 ACPIAM) [ 0.000000] ACPI: RSDT 3FFC0000, 0034 (r1 A M I OEMRSDT 9000528 MSFT 97) [ 0.000000] ACPI: FACP 3FFC0200, 0084 (r2 A M I OEMFACP 9000528 MSFT 97) [ 0.000000] ACPI: DSDT 3FFC0440, 45ED (r1 12345 12345123 123 INTL 2002026) [ 0.000000] ACPI: FACS 3FFCE000, 0040 [ 0.000000] ACPI: APIC 3FFC0390, 0068 (r1 A M I OEMAPIC 9000528 MSFT 97) [ 0.000000] ACPI: MCFG 3FFC0400, 003C (r1 A M I OEMMCFG 9000528 MSFT 97) [ 0.000000] ACPI: OEMB 3FFCE040, 0046 (r1 A M I AMI_OEM 9000528 MSFT 97) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 262080) 1 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1048576 [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0 -> 159 [ 0.000000] 0: 256 -> 262080 [ 0.000000] On node 0 totalpages: 261983 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 1558 pages reserved [ 0.000000] DMA zone: 2377 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 4031 pages used for memmap [ 0.000000] DMA32 zone: 253953 pages, LIFO batch:31 [ 0.000000] Normal zone: 0 pages used for memmap [ 0.000000] Looks like a VIA chipset. Disabling IOMMU. Override with iommu=allowed [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfecc0000] gsi_base[24]) [ 0.000000] IOAPIC[1]: apic_id 2, address 0xfecc0000, GSI 24-47 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Setting APIC routing to physical flat [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Nosave address range: 000000000009f000 - 00000000000a0000 [ 0.000000] Nosave address range: 00000000000a0000 - 00000000000e8000 [ 0.000000] Nosave address range: 00000000000e8000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) [ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs [ 0.000000] PERCPU: Allocating 36096 bytes of per cpu data [ 0.000000] Built 1 zonelists. Total pages: 256330 [ 0.000000] Kernel command line: BOOT_IMAGE=lin2621-rc3 ro root=308 resume=/dev/hda2 splash=silent showopts psmouse.proto=imps console=ttyS0,115200n8 console=tty0 netconsole=6503@192.168.0.107/eth0,6603@192.168.0.101/00:13:20:E3:97:02 debug [ 0.000000] netconsole: local port 6503 [ 0.000000] netconsole: local IP 192.168.0.107 [ 0.000000] netconsole: interface eth0 [ 0.000000] netconsole: remote port 6603 [ 0.000000] netconsole: remote IP 192.168.0.101 [ 0.000000] netconsole: remote ethernet address 00:13:20:e3:97:02 [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 26.805713] time.c: Detected 2200.198 MHz processor. [ 26.805754] Console: colour dummy device 80x25 [ 27.260664] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 27.268547] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 27.284455] Memory: 1023524k/1048320k available (3318k kernel code, 24316k reserved, 1756k data, 220k init) [ 27.371211] Calibrating delay using timer specific routine.. 4405.43 BogoMIPS (lpj=8810871) [ 27.379637] Mount-cache hash table entries: 256 [ 27.384270] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 27.391400] CPU: L2 Cache: 512K (64 bytes/line) [ 27.395942] SMP alternatives: switching to UP code [ 27.400888] ACPI: Core revision 20070126 [ 27.447718] Using local APIC timer interrupts. [ 27.497568] result 12501126 [ 27.500359] Detected 12.501 MHz APIC timer. [ 27.507141] Brought up 1 CPUs [ 27.510305] testing NMI watchdog ... OK. [ 27.554419] NET: Registered protocol family 16 [ 27.558922] No dock devices found. [ 27.562385] ACPI: bus type pci registered [ 27.569033] PCI: Using MMCONFIG at e0000000 - efffffff [ 27.574200] PCI: No mmconfig possible on device 00:18 [ 27.585273] ACPI: Interpreter enabled [ 27.588943] ACPI: (supports S0 S1 S3 S4 S5) [ 27.593247] ACPI: Using IOAPIC for interrupt routing [ 27.607785] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 27.612601] PCI: Probing PCI hardware (bus 00) [ 27.617501] 0000:00:0f.0: cannot adjust BAR0 (not I/O) [ 27.622658] 0000:00:0f.0: cannot adjust BAR1 (not I/O) [ 27.627803] 0000:00:0f.0: cannot adjust BAR2 (not I/O) [ 27.632942] 0000:00:0f.0: cannot adjust BAR3 (not I/O) [ 27.638289] PCI: MSI-K8T-Neo2Fir, attempting to turn soundcard ON [ 27.644379] PCI: MSI-K8T-Neo2Fir, soundcard on [ 27.649084] Boot video device is 0000:02:00.0 [ 27.653833] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 27.659950] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 27.666358] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBPG._PRT] [ 27.672781] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBP0._PRT] [ 27.679196] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBP1._PRT] [ 27.685612] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBP2._PRT] [ 27.692028] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBP3._PRT] [ 27.712507] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 27.719868] ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 10 11 12 14 15) [ 27.727208] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 27.734540] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 27.743044] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 27.751545] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 27.760049] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 27.768550] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14 15) [ 27.775867] Linux Plug and Play Support v0.97 (c) Adam Belay [ 27.781530] pnp: PnP ACPI init [ 27.789843] pnp: PnP ACPI: found 14 devices [ 27.794174] SCSI subsystem initialized [ 27.797998] usbcore: registered new interface driver usbfs [ 27.803520] usbcore: registered new interface driver hub [ 27.808866] usbcore: registered new device driver usb [ 27.813968] PCI: Using ACPI for IRQ routing [ 27.818156] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 27.826540] agpgart: Detected AGP bridge 0 [ 27.833224] agpgart: AGP aperture is 64M @ 0xcc000000 [ 27.838343] pnp: 00:08: ioport range 0xa00-0xa0f has been reserved [ 27.844521] Time: tsc clocksource has been installed. [ 27.849570] pnp: 00:08: ioport range 0x290-0x29f has been reserved [ 27.855741] pnp: 00:08: ioport range 0xa20-0xa2f has been reserved [ 27.861914] pnp: 00:08: ioport range 0xa30-0xa3f has been reserved [ 27.868088] pnp: 00:08: ioport range 0xa40-0xa4f has been reserved [ 27.874266] pnp: 00:09: iomem range 0xffb80000-0xffbfffff has been reserved [ 27.881217] pnp: 00:09: iomem range 0xfff00000-0xfff7fffe has been reserved [ 27.888172] pnp: 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved [ 27.895120] pnp: 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved [ 27.902077] pnp: 00:0c: iomem range 0xe0000000-0xefffffff has been reserved [ 27.909030] pnp: 00:0d: iomem range 0x0-0x9ffff could not be reserved [ 27.915459] pnp: 00:0d: iomem range 0xc0000-0xcffff has been reserved [ 27.921896] pnp: 00:0d: iomem range 0xe0000-0xfffff could not be reserved [ 27.928727] pnp: 00:0d: iomem range 0x100000-0x3fffffff could not be reserved [ 27.936114] PCI: Bridge: 0000:00:01.0 [ 27.939783] IO window: disabled. [ 27.943184] MEM window: disabled. [ 27.946672] PREFETCH window: disabled. [ 27.950595] PCI: Bridge: 0000:00:02.0 [ 27.954258] IO window: c000-cfff [ 27.957660] MEM window: fea00000-feafffff [ 27.961843] PREFETCH window: b7f00000-c7efffff [ 27.966457] PCI: Bridge: 0000:00:03.0 [ 27.970120] IO window: disabled. [ 27.973522] MEM window: disabled. [ 27.977013] PREFETCH window: disabled. [ 27.980933] PCI: Bridge: 0000:00:03.1 [ 27.984596] IO window: disabled. [ 27.988000] MEM window: disabled. [ 27.991489] PREFETCH window: disabled. [ 27.995412] PCI: Bridge: 0000:00:03.2 [ 0.000000] Linux version 2.6.21-rc3 (rddunlap@unicorn) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #3 SMP Fri Mar 9 20:14:58 PST 2007 [ 0.000000] Command line: BOOT_IMAGE=lin2621-rc3 ro root=308 resume=/dev/hda2 splash=silent showopts psmouse.proto=imps console=ttyS0,115200n8 console=tty0 netconsole=6503@192.168.0.107/eth0,6603@192.168.0.101/00:13:20:E3:97:02 debug ignore_loglevel acpi=off [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003ffc0000 (usable) [ 0.000000] BIOS-e820: 000000003ffc0000 - 000000003ffce000 (ACPI data) [ 0.000000] BIOS-e820: 000000003ffce000 - 000000003fff0000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] BIOS-e820: 00000000fecc0000 - 00000000fecc1000 (reserved) [ 0.000000] BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 262080) 1 entries of 256 used [ 0.000000] end_pfn_map = 1048576 [ 0.000000] DMI 2.3 present. [ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 256 used [ 0.000000] Entering add_active_range(0, 256, 262080) 1 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1048576 [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0 -> 159 [ 0.000000] 0: 256 -> 262080 [ 0.000000] On node 0 totalpages: 261983 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 1558 pages reserved [ 0.000000] DMA zone: 2377 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 4031 pages used for memmap [ 0.000000] DMA32 zone: 253953 pages, LIFO batch:31 [ 0.000000] Normal zone: 0 pages used for memmap [ 0.000000] Looks like a VIA chipset. Disabling IOMMU. Override with iommu=allowed [ 0.000000] Intel MultiProcessor Specification v1.4 [ 0.000000] MPTABLE: OEM ID: TEMPLATE MPTABLE: Product ID: ETEMPLATE MPTABLE: APIC at: 0xFEE00000 [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] I/O APIC #1 at 0xFEC00000. [ 0.000000] I/O APIC #2 at 0xFECC0000. [ 0.000000] Setting APIC routing to physical flat [ 0.000000] Processors: 1 [ 0.000000] Nosave address range: 000000000009f000 - 00000000000a0000 [ 0.000000] Nosave address range: 00000000000a0000 - 00000000000e8000 [ 0.000000] Nosave address range: 00000000000e8000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 36096 bytes of per cpu data [ 0.000000] Built 1 zonelists. Total pages: 256330 [ 0.000000] Kernel command line: BOOT_IMAGE=lin2621-rc3 ro root=308 resume=/dev/hda2 splash=silent showopts psmouse.proto=imps console=ttyS0,115200n8 console=tty0 netconsole=6503@192.168.0.107/eth0,6603@192.168.0.101/00:13:20:E3:97:02 debug ignore_loglevel acpi=off [ 0.000000] netconsole: local port 6503 [ 0.000000] netconsole: local IP 192.168.0.107 [ 0.000000] netconsole: interface eth0 [ 0.000000] netconsole: remote port 6603 [ 0.000000] netconsole: remote IP 192.168.0.101 [ 0.000000] netconsole: remote ethernet address 00:13:20:e3:97:02 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 28.786425] time.c: Detected 2200.136 MHz processor. [ 28.786465] Console: colour dummy device 80x25 [ 29.145991] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 29.153871] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 29.169776] Memory: 1023524k/1048320k available (3318k kernel code, 24284k reserved, 1756k data, 220k init) [ 29.256008] Calibrating delay using timer specific routine.. 4405.38 BogoMIPS (lpj=8810778) [ 29.264428] Mount-cache hash table entries: 256 [ 29.269057] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 29.276190] CPU: L2 Cache: 512K (64 bytes/line) [ 29.280730] SMP alternatives: switching to UP code [ 29.285668] Freeing SMP alternatives: 28k freed [ 29.331173] Using local APIC timer interrupts. [ 29.381025] result 12500776 [ 29.383817] Detected 12.500 MHz APIC timer. [ 29.391939] Brought up 1 CPUs [ 29.395139] testing NMI watchdog ... OK. [ 29.439260] NET: Registered protocol family 16 [ 29.443722] ACPI Exception (utmutex-0263): AE_BAD_PARAMETER, Thread FFFF81003FF9F760 could not acquire Mutex [1] [20070126] [ 29.454877] No dock devices found. [ 29.458349] PCI: Using configuration type 1 [ 29.463763] ACPI: Interpreter disabled. [ 29.467607] Linux Plug and Play Support v0.97 (c) Adam Belay [ 29.473274] pnp: PnP ACPI: disabled [ 29.476893] SCSI subsystem initialized [ 29.480720] usbcore: registered new interface driver usbfs [ 29.486251] usbcore: registered new interface driver hub [ 29.491607] usbcore: registered new device driver usb [ 29.496719] PCI: Probing PCI hardware [ 29.500382] PCI: Probing PCI hardware (bus 00) [ 29.505342] 0000:00:0f.0: cannot adjust BAR0 (not I/O) [ 29.510477] 0000:00:0f.0: cannot adjust BAR1 (not I/O) [ 29.515610] 0000:00:0f.0: cannot adjust BAR2 (not I/O) [ 29.520743] 0000:00:0f.0: cannot adjust BAR3 (not I/O) [ 29.526140] PCI: MSI-K8T-Neo2Fir, attempting to turn soundcard ON [ 29.532226] PCI: MSI-K8T-Neo2Fir, soundcard on [ 29.536960] Boot video device is 0000:02:00.0 [ 29.542859] PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0 [ 29.548983] PCI->APIC IRQ transform: 0000:00:02.0[A] -> IRQ 27 [ 29.554807] PCI->APIC IRQ transform: 0000:00:03.0[A] -> IRQ 31 [ 29.560635] PCI->APIC IRQ transform: 0000:00:03.1[B] -> IRQ 31 [ 29.566463] PCI->APIC IRQ transform: 0000:00:03.2[C] -> IRQ 39 [ 29.572290] PCI->APIC IRQ transform: 0000:00:03.3[D] -> IRQ 31 [ 29.578116] PCI->APIC IRQ transform: 0000:00:09.0[A] -> IRQ 18 [ 29.583943] PCI->APIC IRQ transform: 0000:00:0f.0[A] -> IRQ 20 [ 29.589771] PCI->APIC IRQ transform: 0000:00:10.0[A] -> IRQ 21 [ 29.595598] PCI->APIC IRQ transform: 0000:00:10.1[A] -> IRQ 21 [ 29.601426] PCI->APIC IRQ transform: 0000:00:10.2[B] -> IRQ 21 [ 29.607251] PCI->APIC IRQ transform: 0000:00:10.3[B] -> IRQ 21 [ 29.613079] PCI->APIC IRQ transform: 0000:00:10.4[C] -> IRQ 21 [ 29.618907] PCI->APIC IRQ transform: 0000:00:11.5[C] -> IRQ 22 [ 29.624733] PCI->APIC IRQ transform: 0000:00:12.0[A] -> IRQ 23 [ 29.630562] PCI->APIC IRQ transform: 0000:02:00.0[A] -> IRQ 24 [ 29.636537] agpgart: Detected AGP bridge 0 [ 29.643412] agpgart: AGP aperture is 64M @ 0xcc000000 [ 29.648809] PCI: Bridge: 0000:00:01.0 [ 29.652474] Time: tsc clocksource has been installed. [ 29.657535] IO window: disabled. [ 29.660936] MEM window: disabled. [ 29.664424] PREFETCH window: disabled. [ 29.668348] PCI: Bridge: 0000:00:02.0 [ 29.672008] IO window: c000-cfff [ 29.675412] MEM window: fea00000-feafffff [ 29.679594] PREFETCH window: b7f00000-c7efffff [ 29.684211] PCI: Bridge: 0000:00:03.0 [ 29.687870] IO window: disabled. [ 29.691275] MEM window: disabled. [ 29.694764] PREFETCH window: disabled. [ 29.698687] PCI: Bridge: 0000:00:03.1 [ 29.702346] IO window: disabled. [ 29.705752] MEM window: disabled. [ 29.709241] PREFETCH window: disabled. [ 29.713165] PCI: Bridge: 0000:00:03.2 [ 29.716824] IO window: disabled. [ 29.720230] MEM window: disabled. [ 29.723719] PREFETCH window: disabled. [ 29.727642] PCI: Bridge: 0000:00:03.3 [ 29.731299] IO window: disabled. [ 29.734706] MEM window: disabled. [ 29.738195] PREFETCH window: disabled. [ 29.742129] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 29.748400] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 29.754677] PCI: Setting latency timer of device 0000:00:03.0 to 64 [ 29.760953] PCI: Setting latency timer of device 0000:00:03.1 to 64 [ 29.767222] PCI: Setting latency timer of device 0000:00:03.2 to 64 [ 29.773501] PCI: Setting latency timer of device 0000:00:03.3 to 64 [ 29.779783] NET: Registered protocol family 2 [ 29.823521] IP route cache hash table entries: 32768 (order: 6, 262144 bytes) [ 29.830845] TCP established hash table entries: 65536 (order: 9, 2621440 bytes) [ 29.839262] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes) [ 29.846839] TCP: Hash tables configured (established 65536 bind 65536) [ 29.853364] TCP reno registered [ 29.867808] microcode: CPU0 not a capable Intel processor [ 29.873209] IA-32 Microcode Update Driver: v1.14a [ 29.880873] audit: initializing netlink socket (disabled) [ 29.886284] audit(1173471483.616:1): initialized [ 29.890956] Total HugeTLB memory allocated, 0 [ 29.895492] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 29.902034] io scheduler noop registered [ 29.905976] io scheduler anticipatory registered [ 29.910609] io scheduler deadline registered [ 29.914902] io scheduler cfq registered (default) [ 29.919977] vesafb: framebuffer at 0xb8000000, mapped to 0xffffc20000080000, using 3072k, total 16384k [ 29.929272] vesafb: mode is 1024x768x16, linelength=2048, pages=9 [ 29.935357] vesafb: scrolling: redraw [ 29.939020] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 [ 29.957774] Console: switching to colour frame buffer device 128x48 [ 29.977238] fb0: VESA VGA frame buffer device [ 29.987958] Real Time Clock Driver v1.12ac [ 29.992255] Non-volatile memory driver v1.2 [ 29.996604] ppdev: user-space parallel port driver [ 30.001561] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0) [ 30.011008] Linux agpgart interface v0.102 (c) Dave Jones [ 30.016556] [drm] Initialized drm 1.1.0 20060810 [ 30.021303] Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds). [ 30.030480] Hangcheck: Using get_cycles(). [ 30.034716] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 30.042858] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 30.049457] parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] [ 30.190010] parport0: irq 7 detected [ 33.312306] floppy0: no floppy controllers found [ 33.317529] RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize [ 33.325333] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2 [ 33.331478] Copyright (c) 1999-2006 Intel Corporation. [ 33.336791] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI [ 33.343029] e100: Copyright(c) 1999-2006 Intel Corporation [ 33.348736] via-rhine.c:v1.10-LK1.4.2 Sept-11-2006 Written by Donald Becker [ 33.359877] eth0: VIA Rhine II at 0xfebdf800, 00:14:2a:c9:24:d3, IRQ 23. [ 33.367578] eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1. [ 33.375859] tun: Universal TUN/TAP device driver, 1.6 [ 33.384277] tun: (C) 1999-2004 Max Krasnyansky [ 33.393984] netconsole: device eth0 not up yet, forcing it [ 33.403674] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 [ 33.414378] netconsole: carrier detect appears untrustworthy, waiting 4 seconds [ 39.346392] netconsole: network logging started [ 39.356956] Linux video capture interface: v2.00 [ 39.367554] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 39.379902] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 39.394103] Probing IDE interface ide0... [ 39.822501] hda: MAXTOR STM3200820A, ATA DISK drive [ 40.505714] Probing IDE interface ide1... [ 41.381073] hdc: TSSTcorpCD/DVDW SH-W162C, ATAPI CD/DVD-ROM drive [ 42.064308] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 42.074852] ide1 at 0x170-0x177,0x376 on irq 15 [ 42.085422] hda: max request size: 512KiB [ 42.142384] hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63 [ 42.166774] hda: cache flushes supported [ 42.176635] hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 > [ 42.266519] hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache [ 42.279160] Uniform CD-ROM driver Revision: 3.20 [ 42.292608] ehci_hcd 0000:00:10.4: EHCI Host Controller [ 42.303810] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1 [ 42.317211] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfebdfc00 [ 42.328805] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 42.342343] usb usb1: configuration #1 chosen from 1 choice [ 42.353871] hub 1-0:1.0: USB hub found [ 42.363535] hub 1-0:1.0: 8 ports detected [ 42.479994] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 42.493553] USB Universal Host Controller Interface driver v3.0 [ 42.505473] uhci_hcd 0000:00:10.0: UHCI Host Controller [ 42.516608] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 [ 42.529930] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000ec00 [ 42.541590] usb usb2: configuration #1 chosen from 1 choice [ 42.552932] hub 2-0:1.0: USB hub found [ 42.562336] hub 2-0:1.0: 2 ports detected [ 42.675817] uhci_hcd 0000:00:10.1: UHCI Host Controller [ 42.686652] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 [ 42.699680] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000e800 [ 42.711433] usb usb3: configuration #1 chosen from 1 choice [ 42.722578] hub 3-0:1.0: USB hub found [ 42.731782] hub 3-0:1.0: 2 ports detected [ 42.775636] usb 1-7: new high speed USB device using ehci_hcd and address 2 [ 42.855652] uhci_hcd 0000:00:10.2: UHCI Host Controller [ 42.866356] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 [ 42.879221] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000e400 [ 42.890459] usb usb4: configuration #1 chosen from 1 choice [ 42.901394] hub 4-0:1.0: USB hub found [ 42.910381] hub 4-0:1.0: 2 ports detected [ 42.941765] usb 1-7: configuration #1 chosen from 1 choice [ 43.027495] uhci_hcd 0000:00:10.3: UHCI Host Controller [ 43.037919] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5 [ 43.050489] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000e000 [ 43.061436] usb usb5: configuration #1 chosen from 1 choice [ 43.072149] hub 5-0:1.0: USB hub found [ 43.080945] hub 5-0:1.0: 2 ports detected [ 43.994528] usbcore: registered new interface driver libusual [ 44.005258] usbcore: registered new interface driver hiddev [ 44.015711] usbcore: registered new interface driver usbhid [ 44.026060] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 44.037115] PNP: No PS/2 controller found. Probing ports directly. [ 44.048352] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 44.058187] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 44.068199] mice: PS/2 mouse device common for all mice [ 44.110558] input: AT Translated Set 2 keyboard as /class/input/input0 [ 44.129901] input: PC Speaker as /class/input/input1 [ 44.315955] input: ImPS/2 Generic Wheel Mouse as /class/input/input2 [ 44.331156] i2c /dev entries driver [ 44.339437] IPv4 over IPv4 tunneling driver [ 44.348394] GRE over IPv4 tunneling driver [ 44.357261] TCP cubic registered [ 44.365131] NET: Registered protocol family 1 [ 44.374133] NET: Registered protocol family 17 [ 44.383085] NET: Registered protocol family 15 [ 44.391983] ieee80211: 802.11 data/management/control stack, git-1.1.13 [ 44.403154] ieee80211: Copyright (C) 2004-2005 Intel Corporation [ 44.416099] ieee80211_crypt: registered algorithm 'NULL' [ 44.425951] ieee80211_crypt: registered algorithm 'WEP' [ 44.435615] ieee80211_crypt: registered algorithm 'CCMP' [ 44.445329] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3500+ processors (version 2.00.00) [ 44.464659] powernow-k8: 0 : fid 0x2 (1000 MHz), vid 0x12 [ 44.474820] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa [ 44.484813] powernow-k8: 2 : fid 0xc (2000 MHz), vid 0x8 [ 44.494787] powernow-k8: 3 : fid 0xe (2200 MHz), vid 0x8 [ 44.525706] BIOS EDD facility v0.16 2004-Jun-25, 1 devices found [ 44.573224] kjournald starting. Commit interval 5 seconds [ 44.583080] EXT3-fs: mounted filesystem with ordered data mode. [ 44.593399] VFS: Mounted root (ext3 filesystem) readonly. [ 44.603199] Freeing unused kernel memory: 220k freed [ 44.612733] Write protecting the kernel read-only data: 1323k [ 47.738181] lp0: using parport0 (polling). [ 47.746524] lp0: console ready [ 50.008359] PCI: Setting latency timer of device 0000:00:11.5 to 64 [ 51.229047] Adding 2097136k swap on /dev/hda2. Priority:-1 extents:1 across:2097136k [ 51.326123] EXT3 (no)acl options not supported [ 52.010900] EXT3 (no)acl options not supported [ 52.021556] EXT3 FS on hda8, internal journal [ 55.392105] loop: loaded (max 8 devices) [ 55.412844] EXT3 (no)acl options not supported [ 55.509487] kjournald starting. Commit interval 5 seconds [ 55.521249] EXT3 FS on hda1, internal journal [ 55.530519] EXT3-fs: mounted filesystem with ordered data mode. [ 55.560529] EXT3 (no)acl options not supported [ 55.589309] kjournald starting. Commit interval 5 seconds [ 55.609231] EXT3 FS on hda5, internal journal [ 55.618341] EXT3-fs: mounted filesystem with ordered data mode. [ 55.657384] EXT3 (no)acl options not supported [ 55.686536] kjournald starting. Commit interval 5 seconds [ 55.709134] EXT3 FS on hda6, internal journal [ 55.718269] EXT3-fs: mounted filesystem with ordered data mode. [ 82.744547] Time: jiffies clocksource has been installed.